Save Time, Please use Click & Collect

Tesla Brass Compression Adapting Flexible Tap… (6089R)

£ 3.19INC VAT

Add to basket for...

Tesla Brass Compression Adapting Flexible Tap Connectors 15mm x 3/8" 2 Pack (6089R)

Flexible tap adaptors fit into standard 15mm isolating valves. Suitable for flexible hoses/monobloc tails with ¾" swivel nuts.

  • Compression x BSP Male
  • Demountable
  • Suitable for Drinking Water
  • Suitable for Water Systems
  • Suitable for Hard & Soft Water Areas
  • 1 Year Guarantee
  • Helps Prevent Leaks

More Info

View all: Tesla Tap Connectors

Bulk Save Save up to 10%
Bulk savings
QTY Price per item Saving
1 - 2 £3.19 -
3 + £2.86 Save 10%
£3.19INC VAT

Add to basket for...

Tesla Brass Compression Adapting Flexible Tap Connectors 15mm x 3/8" 2 Pack is rated 4.6 out of 5 by 26.
  • y_2020, m_8, d_2, h_15
  • bvseo_bulk, prod_bvrr, vn_bulk_3.0.10
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_26
  • loc_en_GB, sid_6089R, prod, sort_[SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix
  • bvseo_sdk, java_sdk, bvseo-4.0.0
  • CLOUD, getAggregateRating, 21ms
  • REVIEWS, PRODUCT

Add to saved list...

Save
Rated 5 out of 5 by from Great Product I used the adaptor to connect a European tap's flexible tails with 3/8 inch connectors to the top of the isolation valves (1/2 inch). Worked like a dream and did not require excessive force to seal. The tap connectors were happy just finger tight. I needed a collar for the valves (old ones had got misplaced when the previous 1/2 connector flexible tails were fitted directly to the valve) but I had a few lying around and you need to supply an olive for each adaptor. The big feature is that the adaptor adds only 13mm onto the top of the isolation valve, whereas the other type of adaptor that uses a piece of copper pipe adds a lot more. With my basin this is a big issue as the isolators are high up and close to the lower surface of the basin. Add in a good price and good service - wonderful.
Date published: 2020-07-08
Rated 5 out of 5 by from Best fitting These tap connectors are brilliant fittings used for most taps purchased from European and works well.
Date published: 2020-05-19
Rated 1 out of 5 by from Dodgy connector They do not fit into a 15mm isolation valve their outside diameter is too small so the compression olive never compresses enough to seal. With the shaft being too short to put gas tape around this new design is pointless. Tails popped off in a couple of minutes leading to flooding
Date published: 2020-02-18
Rated 5 out of 5 by from The best The best solution for the German plumbing stuff. Easy to install and work ....I Recommend...!!!
Date published: 2019-12-18
  • y_2020, m_8, d_2, h_15
  • bvseo_bulk, prod_bvrr, vn_bulk_3.0.10
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_26
  • loc_en_GB, sid_6089R, prod, sort_[SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix
  • bvseo_sdk, java_sdk, bvseo-4.0.0
  • CLOUD, getReviews, 28ms
  • REVIEWS, PRODUCT

Do I need to use an olive?

I will be using these with a compression valve - do I need to use olives?
Asked by: Euancam
Hello Euancam, I can confirm an olive would need to be used. Thank you for using Q and A.JB
Answered by: jboon
Date published: 2019-02-27

Can I use this as tap tail is too short?

300mm tap tails are just too short to reach isolation valve. Can I use these to effectively extend the tail? Thanks
Asked by: Rodduz
You could but it really not going to add much in length on itself as these are adapters. The 3/8 inch thread screw into your tap tail. The 15mm section goes into any standard 15mm fitting.
Answered by: fdimu
Date published: 2020-02-09

Could anyone share a picture of how this is meant to be fitted

I need to fit a European tap and I thought this adapter was going to help me. I understand the thread is screwed into the female tail end. I don't quite get how the shaft-end of the adapter gets locked into the isolation valve.
Asked by: nyarlathotep77
The screw end goes on your tap tail. The other end is standard 15mm and will fit into any 15mm fitting. It could go straight into a 15mm compression fitting, a speed fit fitting or solder fitting. You isolati9n valve would normally be a compression fitting.
Answered by: fdimu
Date published: 2020-02-09

Are these suitable for push fit connecors?

Are they long enough? Is the brass soft enough for the pushfit teeth?
Asked by: kSpecial
Hi kSpecial, As far as we are aware, these may be suitable for push-fit connectors to go on to the 15mm plain end. A suitable tap connect then goes on to the 3/8"BSP male thread. The more common 15mm x 1/2"BSP connector is Product Code 2665R. I hope this information is of help to you. Thank you for using Q&A>
Answered by: Pebo
Date published: 2020-05-03
  • y_2020, m_8, d_2, h_15CST
  • bvseo_bulk, prod_bvqa, vn_bulk_3.0.10
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_4
  • loc_en_GB, sid_6089R, prod, sort_[SortEntry(order=LOCALE, direction=DESCENDING), SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix
  • bvseo_sdk, java_sdk, bvseo-4.0.0
  • CLOUD, getReviews, 22ms
  • QUESTIONS, PRODUCT
  • bvseo-msg: BV SEO Content for this product did not include verbose reviews.;
Specification
A Size 15 mm
A Size Connection Type Compression
Brand Tesla
B Size 3/8 "
B Size Connection Type BSP Male
Equal/Reducing Adapting
Manufacturer Guarantee 1 Year Guarantee
Max. Pressure @ Max. Temperature 10 bar
Max. Pressure @ Min. Temperature 10 bar
Maximum Operating Temperature 90 °C
Minimum Operating Temperature 1 °C
Pack Size 2
Parent Colour Brass
Pieces in Pack/Case 2
Pipe Fitting Material Brass
Pipe Fitting Product Type Couplers
Pipe Fitting System Compression
Product Type Flexible Tap Connectors