Drayton RTS1 1-Channel Wired Room Thermostat (85263)

£ 16.13INC VAT

Add to basket for...

Drayton RTS1 1-Channel Wired Room Thermostat (85263)

Electronic sensing element. 3-wire installation.

  • 10 to 30°C Temperature Range
  • Suitable for All Boilers
  • 3-Wire Installation
  • Mains-Powered
  • Without Display
  • Double-Insulated
  • Without Frost Protection
  • Fits Standard UK Backplate
  • Energy Saving Trust Approved

More Info

View all: Drayton Wired Thermostats

£16.13INC VAT

Add to basket for...

Add to saved list...

Save
Rated 3 out of 5 by from thermostat Good easy to wire thermostat but had to return first one as had missing terminal. Exchanged no problem but another waste of time and fuel.
Date published: 2022-09-24
Rated 5 out of 5 by from DRAYTON RTS1 Thermostat Great value replacement for the old original one. Clip on to the original base plate to use the existing wiring.
Date published: 2022-09-05
Rated 5 out of 5 by from Easy replacement fix Simple easy replacement fix for RTS1 thermostat. (Please be aware that there are more than one type of thermometer which look very similar from the front) Loosen the two screws at the bottom of the unit and pull the base forward and lift the top off (please note that you may have some silicon or decorators Caulk holding this on) if so, carefully remove this. Remove the front of the unit and look inside. It should state the code and you will need to match this to the replacement unit. Mine was RTS1. If you have the correct replacement unit, you could get away with leaving all of the wiring intact and just placing the new front unit onto the old back plate by slotting the unit over the two location lugs at the top and then tighten up the two screws at the bottom and job done. If you have a little bit of knowledge with DIY, this can be done without paying someone to come and do a 5 min job. Stay warm…
Date published: 2022-04-04
Rated 5 out of 5 by from Drayton Room Thermostat I have just bought a drayton room thermostat from Screwfix and have found that all is now working correctly, it was supplied by Screwfix very quickly and l am pleased with the over all performance of both. I can recommend both Drayton and Screwfix.
Date published: 2022-03-10
  • y_2022, m_9, d_26, h_20
  • bvseo_bulk, prod_bvrr, vn_bulk_3.0.34
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_68
  • loc_en_GB, sid_85263, prod, sort_[SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix
  • bvseo_sdk, java_sdk, bvseo-4.0.0
  • CLOUD, getReviews, 10ms
  • REVIEWS, PRODUCT

My current drayton thermostat has neutral, live,call and earth wires.Do I need a 3 or 4 wire thermostat?

Asked by: Nickop
You need 3 wires, N, L and call
Answered by: Martin, Technical Support
Date published: 2022-03-19

Can this be fitted near boiler

I currently use wireless thermostat & not happy - can this be fitted next to the boiler? Does it have any sensors? Will I need to set up a new mains connection or can I wire this directly into the boiler?
Asked by: MaHQ
The RTS1 thermostat is a Electronic with relay output. Unless connected to a 230v ,mains supply the relay will not operate. it should be mounted on an inside wall about 1.5m (5ft) above the floor in a position where it can respond to room temperature but away from the direct influence of radiators or other appliances giving off heat.
Answered by: Martin, Technical Support
Date published: 2022-02-07

My old stat is only two wire, can I still use this one by looping in a live to the call

Asked by: Anonymous
The RTS1 requires a Neutral, the RTS8 is a 2 wire application
Answered by: Martin, Technical Support
Date published: 2022-01-29

Voltage

Will this work on 5 volt system?
Asked by: Butch123
No you will need volt free which is the RTS4
Answered by: Martin, Technical Support
Date published: 2022-02-08

replacement for Lifestyle ETS1

Hope to use the RTS1 to replace my Lifestyle ETS1. Seems a fairly straightforward swap. Wiring diagram on the ETS 1=Live, 2=Load, 4=Neutral Wiring on Drayton is L, N and 'Call for Heat'. Is the Drayton Call for Heat is the equivalent of ETS 'Load'
Asked by: JimmyFy
yes that is correct the ETS1 load is the call RTS1 terminal 3
Answered by: Martin, Technical Support
Date published: 2022-01-16
  • y_2022, m_9, d_26, h_20CST
  • bvseo_bulk, prod_bvqa, vn_bulk_3.0.34
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_22
  • loc_en_GB, sid_85263, prod, sort_[SortEntry(order=LOCALE, direction=DESCENDING), SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix
  • bvseo_sdk, java_sdk, bvseo-4.0.0
  • CLOUD, getReviews, 9ms
  • QUESTIONS, PRODUCT
  • bvseo-msg: BV SEO Content for this product did not include verbose reviews.;
Specification
Brand Drayton
Central Heating Control Type Thermostats
Colour White
Communication Protocol On/Off
Compatible Boiler Type All Boilers
Control Operation Manual
Current Type AC
Display Type Without Display
ERP Control Class Class I
Fixings Supplied Brackets Supplied
Frost Protection Without Frost Protection
Heating System Mode Heating
Hertz (Hz) 50 Hz
Installation Type 3-Wire Installation
Insulation Type Double-Insulated
IP Rating IP30
Manufacturer Guarantee 1 Year Guarantee
Max. Load (Inductive) 1 A
Max. Load (Resistive) 2 A
Model Name RTS1
Model No 24001SX
Pack Size 1
Pieces in Pack/Case 1
Product Depth 36 mm
Product Height 86 mm
Product Type Room Thermostat
Product Width 86 mm
Receiver Included Receiver Not Included
Sensor Type Electronic Sensor
Smart Compatibility Not Smart
Switching Type SPST
Temperature Range 10 to 30 °C
Terminal Capacity Terminals accept up to 2.5mm² cable
Thermostat Mount Type Fits Standard UK Backplate
Thermostat Power Source Mains-Powered
Thermostat Voltage 230 V
Wireless/Wired Wired