Bearing Separator & Puller (19315)

£ 19.99INC VAT

Add to basket for...

Bearing Separator & Puller (19315)

Effective tool for pulling and separating bearings.

More Info

View all: Unbranded Gear & Bearing Tools

£19.99INC VAT

Add to basket for...

Add to saved list...

Save
Rated 5 out of 5 by from Brilliant product This is a great bit of kit. I was unhappy with the idea of hitting the stuck bearings on my trailer axles with a lump hammer (as some people advise), so invested in this set. I needed to use longer bolts than the ones supplied in order to extend the puller to the length of the axles - so an extra cost there - but the stuck bearings then came off without any drama at all. There are decent videos on Youtube if you want to see a product like this being used before you buy.
Date published: 2021-04-13
Rated 5 out of 5 by from Bearing gear puller I used this to remove a 2t crankshaft main bearing that was very close with not much room. Set it up level it was highly effective. Well recommended product.
Date published: 2020-10-23
Rated 3 out of 5 by from Will it pull any bearing? This tool comes in two parts. Both parts are well made, however one part works well, the other not so well. The bearing separator works well as long as there is sufficient space to get the collar behind the bearing. Just tighten the bolts progressively and the bearing starts to move. The other part works by having two bolts screwed into the bearing carrier then a central bolt is tightened to push against the center of the axle/shaft.The central bolt is fitted with a push fit pivot on the end which has a small hole in the centre intended to stop it slipping off the shaft, assuming it has a small ball on the end of the shaft that sits in the hole in the pivot. Quite often, the shaft also has a hole in the end assuming the puller will have a ball on the end of the pivot bolt. When both have holes, a two leg puller invariably slips off when under load.If this tool came with a second push on pivot with a ball on the end it would cope with either scenario. The quality of both items are perfectly adequate, but sadly, I don't have bolt holes in my bearing carrier and do have a hole in the end of my axle shaft so was unable to use this tool.
Date published: 2020-09-13
Rated 5 out of 5 by from Hi from north East England Aud I used this to assist the realise of a bearing. When in the press I was told to put the mettle press plates below the screw part of this product to avoid damage to the product. I did this and it worked effectively
Date published: 2020-08-03
  • y_2021, m_7, d_24, h_23
  • bvseo_bulk, prod_bvrr, vn_bulk_3.0.18
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_25
  • loc_en_GB, sid_19315, prod, sort_[SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix
  • bvseo_sdk, java_sdk, bvseo-4.0.0
  • CLOUD, getReviews, 23ms
  • REVIEWS, PRODUCT

Can this be attached to a slide hammer? If so, what's the thread?

Asked by: GSDavies
Hello GSDavies, No, this would not be able to be used with a slide hammer. Thank you for using Q&A
Answered by: SWake
Date published: 2021-03-09

Bolt Dimensions

Of the 2 silver bolts pictured, what are the dimensions? Thread size, bolt length, metric or imperial, etc.
Asked by: Mikeinho

Washing machine?

Would this work on washing machine bearings please?
Asked by: Kalaztra
Hello Kalaztra, As far as we are aware it possible might as there is no information saying if it can or not. Thank you for using Q&A,[BH].
Answered by: yeldarb
Date published: 2020-12-13

Bearing puller

Could you please tell me the effective min and max size of the bearing separator? Thanks
Asked by: jonone
Hello, The pull plate has a range of 30-50mm. Thank you for using Q&A.
Answered by: LAWR
Date published: 2020-02-07

What dimensions does this have?

How long is the reach? How wide can it go?
Asked by: easypie
Hi easypipe We have been advised by our warehouse that the reach is approximately 90mm and the maximum width is 50mm. Thanks for using Q&A
Answered by: DEDMONDS
Date published: 2021-07-02
  • y_2021, m_7, d_24, h_23CST
  • bvseo_bulk, prod_bvqa, vn_bulk_3.0.18
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_7
  • loc_en_GB, sid_19315, prod, sort_[SortEntry(order=LOCALE, direction=DESCENDING), SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix
  • bvseo_sdk, java_sdk, bvseo-4.0.0
  • CLOUD, getReviews, 14ms
  • QUESTIONS, PRODUCT
  • bvseo-msg: BV SEO Content for this product did not include verbose reviews.;
Specification
Manufacturer Guarantee 1 Year Guarantee
Pack Size 1
Pieces in Pack/Case 1
Product Type Bearing Separator & Puller