Rated 5 out of
5
by
diyfan50 from
Superb saw.
Excellent table saw,i have seen a couple of bad reviews for this saw but they are obviously written by people that just dont understand basic diy when it comes to assembling tools.These saws are quick and easy to build and use ,giving good accurate cuts.excellent value for money.
Date published: 2021-03-20
Rated 2 out of
5
by
John1979 from
Saw table
When I finally managed to assemble it the actual saw is accurate and powerful however the instructions on assembly were worse than useless and the cross cut fence is poor
But the worst part is the removable cheap plastic plate surrounding the blade which broke on first using the saw I informed the manufacturer and after receiving an initial replay have heard nothing more for two months
Date published: 2021-02-01
Rated 4 out of
5
by
smurkenstein from
After 2 months, very pleased
This is my first table saw which I bought to construct a timber frame greenhouse..
Pros:
Once calibrated with an angle measure the blade gives consistent, accurate cuts to within 0.2 degrees - the angle and height settings a pretty close to what you get.
The mitre fence is difficult to set up but once you have it just right it is great - it rolls on bearings and a bar and is a pleasure to work with
Very firm adjustment on the ripping fence which is great
Cons (none of the below are killers):
Sheppach don't respond to technical requests by email and don't answer the phone
The assembly manual is poor and the riving knife configuration is nothing like the one shown in the manual - the dust shield is not usable for deep rips and mitres
The aluminium table extension is wobbly so think about adding a prop to it
The saw plate is plastic and a bit flimsy (not a big deal)
Push stick is ok, but I don't trust the included grip tool as it brings you too close to the blade, imho
Overall, its was a good purchase - definitely worth the investment for a DIYer
Date published: 2019-07-31
Rated 3 out of
5
by
Beja from
Good if you know what your doi
The assembly instructions are useless. If you've done one before you'll get by. Mine was supplied without the cable and plug. Screwfix were useless but the manufacturer was brilliant.the pre-assembled blade was not parallel to the fence. Nothing in the instructions but can be fixed if you've done it before. The mitre fence is a disaster. The assembly brackets foul the travel of the parallel fence so mine had to go leaving a very basic table saw. That makes it expensive but what is left is brilliant at what it does. Not much better on the market at this price
Date published: 2019-06-17
Does this table saw fold up for storage?
Asked by: Stevieboy1981
Hi,
This table does not fold up for storage.
Answered by: Scheppach-Expert
Date published: 2020-12-21
What are the sound levels from this saw?
Asked by: Livingston
Hi,
operation L = 112,4 dB (A)
Answered by: Scheppach-Expert
Date published: 2020-12-12
Do you sell additional blades to order at the same time and if so can you advise on the part number and price?
Asked by: PmartinR
Hello The sawblades are 315mm x 30mm bore x 3.2mm kerf please ask when ordering as you may require a fine cutting blade or ripping blade ( this model is supplied with a course ripping blade 24 teeth as standard ) , the help line can put you in contact with the manufacturer with your requirements .
Answered by: Scheppach-Expert
Date published: 2020-03-08
We have bought this table saw but there isn’t anything supplied to plug into the mains electrical supply, is this an additional product that you should have supplied or something I need to purchase? If so could you advise what we need. Thank you
Table saw HS120 / TS310
Asked by: Jonnysus
Hello Please contact the screwfix help centre with your delivery details and we can post the electrical lead directly to you .
Answered by: Scheppach-Expert
Date published: 2020-03-07
How do you fit a feather board to this table?
Seeing as the top doesn’t have any channels...
Asked by: Womblebreath
Hello A feather board provides side or top pressure and is not really necessary on this model , this model is classed as a site saw , and site saws do not have a slot in the table top as they are made of fabricated sheet steel .Please look at the scheppach ts 82 this may be better for you .
Answered by: Scheppach-Expert
Date published: 2019-07-08
| Specification |
| Bevel Angles |
0 - 45 ° |
| Blade Description |
TCT Blade |
| Blade Diameter |
315 mm |
| Brand |
Scheppach |
| Brushless |
Brushless |
| Corded Tool Weight |
53 kg |
| Cutting Depth Capacity |
83 mm |
| Disc Bore Size |
30 mm |
| Manual or Powered |
Powered |
| Manufacturer Guarantee |
2 Year Manufacturer's Guarantee (T&Cs Apply) |
| Max. Bevel Angles (L/R) |
49° - 0° |
| Max. Cutting Depth At 90deg |
83 mm |
| Model No |
HS120 |
| No Load Speed |
2800 rpm |
| Number of Teeth |
24 |
| Pack Size |
1 |
| Pieces in Pack/Case |
1 |
| Plug Included |
Includes Plug. |
| Power Output (Watts/Kw) |
2200 W |
| Power Supply |
Electric |
| Power Voltage Supply |
240 V |
| Product Height |
1100 mm |
| Product Length |
1730 mm |
| Product Type |
Table Saw |
| Product Width |
840 mm |
| Table Length |
800 mm |
| Table Width |
550 mm |
| Total Product Weight |
52 kg |
Product contents
HS120, 24-tooth TCT ripping blade, sliding table carriage, rear extension table, wheel kit, lifting handles, rip fence, blade spanner, plastic blade guard and extraction hose.
Downloads
Instruction Manual
*Delivered direct from our suppliers in the number of working days stated on the delivery button
