As an essential retailer, our stores remain open across the UK

Easydrive Countersunk Concrete Screws 7.5 x 80mm 100… (8400H)

£ 11.99INC VAT

Add to basket for...

Easydrive Countersunk Concrete Screws 7.5 x 80mm 100 Pack (8400H)

Ideal for fixing uPVC and timber frames directly to masonry.

  • Flat Countersunk Head with 5 x Locking Ribs
  • Deep High / Low Thread for High Pull-Out Resistance
  • Pilot Hole Required
  • Suitable for Both Domestic & Trade Use
  • Heat-Treated
  • Zinc & Yellow-Plated

More Info

View all: Easydrive Masonry Screws

£11.99INC VAT

Add to basket for...

Easydrive Countersunk Concrete Screws 7.5 x 80mm 100 Pack is rated 4.8 out of 5 by 317.
  • y_2021, m_1, d_26, h_17
  • bvseo_bulk, prod_bvrr, vn_bulk_3.0.13
  • cp_1, bvpage1
  • co_hasreviews, tv_1, tr_316
  • loc_en_GB, sid_8400H, prod, sort_[SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix
  • bvseo_sdk, java_sdk, bvseo-4.0.0
  • CLOUD, getAggregateRating, 31ms
  • REVIEWS, PRODUCT

Add to saved list...

Save
Rated 5 out of 5 by from Great screws! I have used these for a garage conversion in my house and they work really well. Built a stud wall and batten for dry lining and the fixings are going into the walls floor and ceiling like a dream. Use the correct size drill bit to the correct depth and you won't go wrong. Really good bit of kit and saves with all the faff of screws and raw plugs.
Date published: 2021-01-20
Rated 5 out of 5 by from Did the job Very good. Did the job well. Dont think they'll be coming out in a hurry. Drill bit included for the star head so that was handy.
Date published: 2021-01-20
Rated 4 out of 5 by from Brilliant screws - fixing tips Great screws with strong grip but hole size is critical. I used a 5.5mm drill (6mm specified). One of the 6 screws (into an internal birck wall) wound straight in the others went in by different amounts(torque limit tripped on cordless drill). Always make sure holes are 10mm deeper than the screws and rattle the drill in and out a few times to clear the dust. If the screw starts binding at less than half depth don't force it. Take it out and either re drill at 6mm or wind the drill in and out a few time while gently applying side pressure in a circular motion to slightly open the hole. When the screw goes in over half way then binds remove it, squirt a small dab (size of 2 peas) of silicon sealer in the hole and the screw should go in fine. Best to do this on final fit incase the screw gets permanently locked when the silicon sets BobP
Date published: 2021-01-15
Rated 5 out of 5 by from Great screw Good screw cuts well in blocks and drives in easily.
Date published: 2021-01-11
  • y_2021, m_1, d_26, h_17
  • bvseo_bulk, prod_bvrr, vn_bulk_3.0.13
  • cp_1, bvpage1
  • co_hasreviews, tv_1, tr_316
  • loc_en_GB, sid_8400H, prod, sort_[SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix
  • bvseo_sdk, java_sdk, bvseo-4.0.0
  • CLOUD, getReviews, 19ms
  • REVIEWS, PRODUCT

What’s the max torque these can take before ripping out the thread that’s being tapped into the masonry? Thanks

Asked by: Royceyy
Hello Royceyy, The breaking torque for this product is 204 kgf/cm Thank you for using Q&A
Answered by: Cwalm
Date published: 2020-12-07

Fixing wall hung toilet frame to grey dense block

Is it a good product to fix wall hung toilet frame to grey dense blocks? I would use 2 screws on top, 4 in the middle and 2 into the floor.
Asked by: Anonymous
Hello Anonymous, We are not able to recommend whether this item is best suited for your requirements unfortunately. Thank you for using Q&A
Answered by: SWake
Date published: 2020-11-02

What size TX bit do these require?

Asked by: Miked1118
Hello, These screws require TX30 bit. Thanks for using Q&A. [DG]
Answered by: DGIFF
Date published: 2020-10-20

If fixing into regular brick work how strong are these fixings in KN

Asked by: grumpyaries
Hello, Max. Pull out load:400 kgf, max. shear load 150kgf, (These figures are based on resting with they are C20 concrete). Thanks for using Q&A. [DG]
Answered by: DGIFF
Date published: 2020-11-02

What Screw depth needed into brick to fix 4x2 wall plate

Asked by: Doghousedave
  • y_2021, m_1, d_27, h_17CST
  • bvseo_bulk, prod_bvqa, vn_bulk_3.0.13
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_142
  • loc_en_GB, sid_8400H, prod, sort_[SortEntry(order=LOCALE, direction=DESCENDING), SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix
  • bvseo_sdk, java_sdk, bvseo-4.0.0
  • CLOUD, getReviews, 13ms
  • QUESTIONS, PRODUCT
  • bvseo-msg: BV SEO Content for this product did not include verbose reviews.;
Specification
Brand Easydrive
Colour Zinc & Yellow-Plated
Drilling Action Pilot Hole Required
Drive Type TX
Head Type Countersunk
Indoor/Outdoor Usage Indoor
Manufacturer Guarantee 1 Year Guarantee
Max Fixture Depth 50 mm
Pack Size 100
Pieces in Pack/Case 100
Product Diameter 7.5 mm
Product Length 80 mm
Product Type Concrete Screws
Screw Diameter (mm) 7.5 mm
Screwdriver Type TX
Suitable Use Type Suitable for Both Domestic & Trade Use
Thread Length Fully Threaded