Browse store

Manrose Cooker Hood Termination Kit 125mm (17489)

HIPS polystyrene. For use with 125mm cooker hood outlets. Suitable for commercial and domestic use. Suitable for use with gas appliances. Compliant with Part F of the Building Regulations.

  • Vent Colour: Grey
  • Vent Width: 140mm
  • Channel Width: 125mm
  • Hose Length: 1.5m
  • Model No: 43076
  • 3 Year Manufacturer's Guarantee (T&Cs Apply)
  • Vent Colour: Grey

More Info

£12.99INC VAT

Add to basket for...

Manrose Cooker Hood Termination Kit 125mm is rated 3.7 out of 5 by 50.
  • y_2017, m_7, d_19, h_13
  • bvseo_bulk, prod_bvrr, vn_bulk_1.0.0-hotfix-1
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_50
  • loc_en_GB, sid_17489, prod, sort_[SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix

Add to saved list...

Save
Rated 4 out of 5 by from terminator too. An excellent buy from Screwfix, terrific service speed and great product. Miles better than flimsy plastic hose but watch out for the sharp edges on the aluminium. Would be even better with two clips - one for each end.
Date published: 2017-07-06
Rated 5 out of 5 by from Easy to fit I found this duct kit very straightforward and easy to use. I would highly recommend wearing gloves as the 'raw' edges of the aluminium duct pipe are particularly ferocious.
Date published: 2017-06-19
Rated 4 out of 5 by from size of hole you drill ? Do not use the 127mm. diamond core drill with this kit. The external measurement of the tube is 130mm. A 140 core drill is recommended but for some strange reason Screwfix don't sell one. No joined up thinking there. Your only option is the 150mm. Then make good ......with foam or filler. The Eurbauer 150.. went through my block work like a knife though butter even on a medium size SDS dill ( with clutch) But it was only block work...hard bricks will no doubt take a bit longer. Went through the cavity wall first with a 400mm 10mm drill....then poked a pilot drill into the core drill and off we went. You can take the small pilot drill out after you get going.10 mins later all done. Work from both sides of the wall towards the cavity..inside first..get someone to hold a hoover nozzle up to the drill it will take 80% of the dust away.....stick a bit of rolled up newspaper into the hole when you reach the cavity to stop the outer skin dust going coming indoors and go outside to drill into the cavity from the other side. Two other things Screwfix....the exterior plastic grill should be brick red.....and 2 jubilee clips would be better than one.
Date published: 2017-02-23
Rated 5 out of 5 by from Works as it should Does exactly what it's supposed to do, cheap and cheerful can't go wrong
Date published: 2017-02-16
  • y_2017, m_7, d_19, h_13
  • bvseo_bulk, prod_bvrr, vn_bulk_1.0.0-hotfix-1
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_50
  • loc_en_GB, sid_17489, prod, sort_[SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix

On the 125mmcooker hood ducting kit what is the outside dimensions of the gravity louvre? Spec says 140 but that is same as 100 kit and wall hole size for 125 kit in instructions. Is it actually art no 94320 which is 160 x 160?

Asked by: Nicknamesareawasteofspace
The Facia of the External Grille measures 163x163mm.
Answered by: Ventilation experts
Date published: 2017-06-17

120/150 ducting kit

Hello, I'm buying the belling 60CHIM cooker hood, the manufacturer says a 120/150 ducting kit is needed, I have no clue what this is! What do I need to buy? Help greatly appreciated Thanks Leigh
Asked by: LeighB

im really stuck literally od id prob

got this kit and went to bore a hole in wall with 127mm core(largest size available before going hard core) but just in time stopped and measured od of this kit its 132 mm how can i get over this prob is there a reducer i can use to reduce hose size to say 120mm id .why does this constantly happen cant the industry get this standardised ive been caught before with plumbing.
Asked by: jezman
I was puzzled by this one too, but the instructions say to bore a 140 mm hole, which I did and that works fine, gives enough room for error.
Answered by: Snewzer
Date published: 2017-06-16

how easy is it to cut hose to required length

do you have to extend fully to measure for trimming length
Asked by: jezman
Hi, Ducting can be cut down to suit. It does not have to be fully extended.
Answered by: Ventilation experts
Date published: 2016-09-04

On the flat channel ducting 204 mm , are there any 90 degree horizontal or vertical bends ?

Due to the nature of where extraction needs to exit outer wall , once placed over wall units , need for a horizontal 90 degree bend . this is to avoid the change from channel ducting to round ducting to exit outer wall . Preferred would be for round 125 mm , but no round 90 degree 125 mm bends available . Thank you for your time Robin
Asked by: Rhoridge
Hello, I do apologise for the delay in replying. Unfortunately this part is not available within screwfix and will have to be sourced directly from the manufacturer. Hope this helps. Regards
Answered by: Ventilation experts
Date published: 2015-11-23
  • y_2017, m_7, d_19, h_24CST
  • bvseo_bulk, prod_bvqa, vn_bulk_1.0.0-hotfix-1
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_5
  • loc_en_GB, sid_17489, prod, sort_[SortEntry(order=LOCALE, direction=DESCENDING), SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix
Specification
Brand Manrose
Channel Width 125 mm
Colour Grey
Fixings Supplied Fixings Supplied
Manufacturer Guarantee 3 Year Manufacturer's Guarantee (T&Cs Apply)
Model No 43076
Pack Size 1
Pieces in Pack/Case 1
Product Diameter 125 mm
Product Type Cooker Hood Termination Kit

Spigot dia: 125mm. Ducting length: 1.5m. Fixings Supplied.

Product contents

1.5m hose, gravity grille, worm and fixings.

Downloads

Instruction Manual