Browse store

Armeg SDS Plus Channelling Chisel 30mm (16724)

Quick, easy installation of cables, wire and copper pipe, giving a clean finish.

More Info

£36.99INC VAT

Add to basket for...

Armeg SDS Plus Channelling Chisel 30mm is rated 4.2 out of 5 by 37.
  • y_2017, m_7, d_25, h_13
  • bvseo_bulk, prod_bvrr, vn_bulk_1.0.0-hotfix-1
  • cp_1, bvpage1
  • co_hasreviews, tv_1, tr_36
  • loc_en_GB, sid_16724, prod, sort_[SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix

Add to saved list...

Save
Rated 5 out of 5 by from Worth the outlay! Decided to bite the bullet and buy an SDS drill and this tool...so glad I did, saves hours over the cold chisel and hammer!! I still run a grinder down both sides, and let the chisel clean out the centre. You don't have to but it makes for a neater finish. Expensive yes, but so worth the outlay.
Date published: 2017-07-17
Rated 5 out of 5 by from Buy one! If you need to do a lot of chases then get one of these. Cuts through brick and breeze block with ease. Can't fault the item apart from being an expensive purchase when i personally will only use it the once.
Date published: 2017-06-26
Rated 2 out of 5 by from Ok until it broke Was a happy purchaser as it did do what it should have done, only problem was that after less than one day's work it broke. Chisel edge showed slight signs of wear but the bits shank broke, actually within the chuck. Luckily the broken piece came out and Screwfix refunded the tool without question. If Armeg put a bit more into producing a good unbreakable shank then it would be a tool worth the money, unfortunately that is not yet.
Date published: 2017-06-16
Rated 4 out of 5 by from Channeling chisel This chisel is ideal for blocks and soft bricks, was a bit of a struggle going through the render leaving a bit of a messy channel
Date published: 2017-06-12
  • y_2017, m_7, d_25, h_13
  • bvseo_bulk, prod_bvrr, vn_bulk_1.0.0-hotfix-1
  • cp_1, bvpage1
  • co_hasreviews, tv_1, tr_36
  • loc_en_GB, sid_16724, prod, sort_[SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix

Does this work with any sds drill

Asked by: Dolmanator
Hi, The channeling chisels will work with most SDS+ drilling machines. You just need to make sure that the power tool has the ability to turn off the rotation and work purely on hammer action (chiseling function). Also, you should not use continuously for more than 15 minutes, lubricate the SDS+ shank with grease before and during use and limit the amount of "levering" you do with the chisel.
Answered by: Armeg Tech
Date published: 2017-04-19
  • y_2017, m_7, d_25, h_24CST
  • bvseo_bulk, prod_bvqa, vn_bulk_1.0.0-hotfix-1
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_1
  • loc_en_GB, sid_16724, prod, sort_[SortEntry(order=LOCALE, direction=DESCENDING), SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix
Specification
Brand Armeg
Manufacturer Guarantee 1 Year Guarantee
Model No G225B4CC
Pack Size 1
Pieces in Pack/Case 1
Product Diameter 30 mm
Product Length 225 mm
Product Type SDS Plus Channelling Chisel
Product Width 30 mm
Suitable Use Type Suitable for Use on Most Masonry
Total Product Weight 0.37 kg

30mm and 55mm channelling chisels for installing cables, wires, casing and conduit. Suitable for use on most masonry. 20mm extended version for gaining access behind skirting board. Use SDS plus machine with roto-stop.