Browse store

Zinsser Bulls Eye 1-2-3 Primer-Sealer 2.5Ltr (10136)

Interior and exterior, water-based, primer / sealer. Adheres to all surfaces without sanding. Blocks stains, permanently sealing graffiti, grease spots, tar and asphalt, indoors and out. Low odour application and conveniently quick-drying with excellent adhesion to even glossy surfaces. Contains a biocide that protects the dried coating against fungal degradation. Dry in 30 minutes. Recoat in 60 minutes. Covers approx. 10m²/Ltr.

  • Touch-Dry in 30mins
  • Recoat After 45mins
  • Excellent Adhesion Without Sanding
  • Prevents Rust Formation
  • Biocide Protects Against Fungal Degradation
  • Blocks Stains & Permanently Seals
  • Suitable for Indoor & Outdoor Use

More Info

£32.99INC VAT (£13.20/Ltr)
Was £37.99 Save £5.00 (13%)

Add to basket for...

Zinsser Bulls Eye 1-2-3 Primer-Sealer 2.5Ltr is rated 4.7 out of 5 by 114.
  • y_2017, m_6, d_27, h_10
  • bvseo_bulk, prod_bvrr, vn_bulk_1.0.0-hotfix-1
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_114
  • loc_en_GB, sid_10136, prod, sort_[SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix

Add to saved list...

Save
Rated 5 out of 5 by from It's good Used for priming and sealing MDF, works really good on sealing the newly cut edges
Date published: 2017-06-21
Rated 5 out of 5 by from Always delivers Used mainly for preparing skirting boards/door-frames. Easy to apply and allows for a perfect coat of gloss. Fantastic product.
Date published: 2017-05-30
Rated 5 out of 5 by from Top Quality. This primer adheres very well to most household surfaces and brushes on easily. It is ideal for priming old gloss paintwork as you do not have to sand the gloss down first - just give it a good clean with sugar soap to get rid of any grease or grime then apply the primer.
Date published: 2017-05-25
Rated 2 out of 5 by from Is it just me. I bought this as an alternative to the red tin BIN which I found to be hard work and unforgiving (more than 1 brush stroke and and it behaves more like tacky glue). This on the other hand was like applying a thinned down coat of emulsion. Runs badly if your not careful. Took 3 coats to get a decent finish. Not as sandable as BIN as it peels very easily. I applied it to a long varnished balustrade and the spindles were a nightmare to do. Very poor finish compared to red tin BIN which dried rock solid with really good adhesion.I think I would have been better off with a bog standard Dulux undercoat but wasnt sure if this would adhere to the gloss varnish, I might use the red tin BIN again (I need to get quicker with my brush strokes) but not this version which simply didnt work for me.
Date published: 2017-05-18
  • y_2017, m_6, d_27, h_10
  • bvseo_bulk, prod_bvrr, vn_bulk_1.0.0-hotfix-1
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_114
  • loc_en_GB, sid_10136, prod, sort_[SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix

I have had efflorescence on an internal wall. The damp problem has been fixed and the efflorescence removed with an acid-based cleaner. Is BullsEye 123 a suitable primer before repainting with a topcoat?

Asked by: DGGREMLIN
Hi. Thank you for your enquiry. Our best recommendations for this particular surface would be to ensure the acid based cleaner has been completely rinsed off and the surface is completely free from salts. Application of the Bullseye 1-2-3 will not stop further salts so it is very important to ensure they have run their course and been removed. Bullseye 1-2-3 is a suitable primer/sealer for most surfaces including plaster and dry wall so would be an ideal choice for priming the surface. 1 or 2 coats are recommended to be applied with either a brush or a roller at a coverage rate of 10m²/L/coat. Once it is completely dry (minimum of 1 hour) you can overcoat it with your chosen decorative topcoat, oil based or water based. Hope this helps.
Answered by: Zinsser Product Support
Date published: 2017-06-15

Which is the best zinsser stain killer to use on stained interior bathroom doors

Wanted to have a satin finish
Asked by: Tinkeyfish
Hi. Thank you for your recent enquiry. Our best recommendation for this particular surface would be the Zinsser Cover Stain (I litre = 17114 or 2.5 litres = 17117). It provides excellent blocking properties and has unparalleled adhesion to any surface providing great key without have to scuff sand. Always ensure that the surface has prepared sufficiently i.e., with hot soapy water then rinsed with fresh warm water to remove detergent and when dry a good wipe with methylated spirit. 1 or 2 coats are recommended to be applied with either a brush or a roller at a coverage rate of 10m²/L/coat. Once the cover Stain is completely dry (minimum of 1 hour) you can overcoat it with your chosen decorative topcoat, oil based or water based. Zinsser Perma-White Interior Satin (1 litre = 13040 or 2.5 litres = 62096)would be a suitable finishing coat. 2 coats are recommended to providing a durable, cleanable, long lasting decorative finish that stays white, does not yellow and can be over coated after a minimum of 2 hours. Hope this helps.
Answered by: Zinsser Product Support
Date published: 2017-06-15

Does this paint cover wood knots in pine panelling successfully?

Asked by: Fdbjfbrjdjdnfsrgd
Hi. Thank you for your enquiry. Our best recommendation for sealing knots is the Zinsser B-I-N (1 litre = 29661, 2.5 litre = 10130 or 5 litres = 3298G). It's shellac base provides excellent adhesion and will seal bleeding knots and sap streaks. 1 or 2 coats of B-I-N primer is recommended, to be applied by brush or roller at a coverage rate of approx. 10m²/L/coat. Always ensure that the surface has prepared sufficiently i.e., with hot soapy water then rinsed with fresh warm water to remove detergent and when dry a good wipe with methylated spirit. I hope this helps.
Answered by: Zinsser Product Support
Date published: 2017-06-05

Hi there have a ceiling that I am going to skim coat but the original paint is silk finish will bin 123 work as a sealer and bond coat for the compound

Asked by: Scottee
Hi. Thank you for your enquiry. The Zinsser Bullseye 1-2-3 is a tried and tested primer/sealer for under painted surfaces. As we have not tested this as a primer/sealer under a skim coat our best advice would be to contact the skim coat manufacturers for advice as to what it can be applied to. I hope this helps.
Answered by: Zinsser Product Support
Date published: 2017-06-06

Zinsser Bullseye Plus??

What's the difference between this product and the 123 Plus please? Planning to use for painting tiles.
Asked by: Mrsmclaren
Hi Mrsmclaren. Thank you for your recent enquiry. The main difference between the Bullseye 1-2-3 and the 1-2-3 plus is the high hiding/stain blocking qualities, the plus being more enhanced. The Bullseye 1-2-3 would be the perfect choice for applying to tiles, it will certainly stick to the surface and provide and excellent key for your chosen top coat, oil or water based, I hope this helps.
Answered by: Zinsser Product Support
Date published: 2017-06-15
  • y_2017, m_6, d_27, h_16CST
  • bvseo_bulk, prod_bvqa, vn_bulk_1.0.0-hotfix-1
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_96
  • loc_en_GB, sid_10136, prod, sort_[SortEntry(order=LOCALE, direction=DESCENDING), SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix
Specification
Brand Zinsser
Coating & Finishing Type Matt
Coating Finishing Volume 2.5 Ltr
Colour White
Coverage Per Litre 10 m² per litre
Manufacturer Guarantee 1 Year Guarantee
Pack Size 1
Parent Colour White
Pieces in Pack/Case 1
Product Type Bulls Eye 1-2-3 Primer-Sealer
Volume 2.5 Ltr

Downloads

Safety Data Sheet (COSHH)