Browse store

Waste Manifold Grey SP588 (22367)

Designed to fit a soil stack in the corner of a room. Allows connections to 32mm, 40mm and 50mm waste inlets and helps prevent stack induced siphonage on connecting runs. Four waste connections possible. Single open boss.

  • Simple Push-Fit Connection for All Waste Pipes
  • Self-Cleansing Design

More Info

£16.79INC VAT

Add to basket for...

Rated 4.8 out of 5 by 5 reviewers.
  • 2016-05-27 T10:43:15.851-05:00
  • bvseo_lps, prod_bvrr, vn_prr_5.6
  • cp-1, bvpage1
  • co_hasreviews, tv_5, tr_5
  • loc_en_US, sid_22367, prod, sort_default

Add to saved list...

Rated 4 out of 5 by Take care with the seals As others have said this is a very useful fitting. It is over 90° from face to face but this takes into account the spacing from the wall when pipe brackets are used. If it's tight chase the wall out and rotate it a bit - don't chop into the joist as one reviewer says. Based on experience a word of warning about the smaller seals: Hold them in place both when inserting and removing a pipe. I lost a seal down the stack on pulling a pipe out of it. Managed to recover it later with the help of a sieve on a stick but you might not be so lucky. 11 May 2016
Rated 5 out of 5 by Best fit for limited space Well designed and good value for money product. Incorporates a flush to soil pipe design, so it fits tight into a corner or against a wall. Eliminates the need for additional boss adaptors on the main pipe for up to 4 appliances. 2 Mar 2016
Rated 5 out of 5 by Great manifold Great manifold, great valve for money, low profile/low level, multiple ports, just what I needed. 12 Nov 2015
Rated 5 out of 5 by A nice solution I needed something like this to connect up bath, shower and basin wastes below a wc connection but where there was limited space. I tried one from tool station that had a rib all around where the top and bottom halves of the chamber met that fouled on the adjacent joist. This looked like a better prospect as the chamber is flush with the line of the outside of the pipe. One thing that was not obvious from the picture is that the angle between the two straight faces is significantly more than 90 degrees to accomodate the four inlets. I had to chop some material from the adjacent joist to make room. If it's bracketed off a wall then there should be adequate space for it.. As I said above it's a great solution and at a reasonable price. I cannot really comment on the performance or reliability yet but I have no reason to doubt that it will perform well. 20 Jan 2015
  • 2016-05-27 T10:43:15.851-05:00
  • bvseo_lps, prod_bvrr, vn_prr_5.6
  • cp-1, bvpage1
  • co_hasreviews, tv_5, tr_5
  • loc_en_US, sid_22367, prod, sort_default
Page : 2 next>
1 Question  1 Answer

Screwfix Q&A

Ask your questions. Share your answers.

« Back
20 May 2016
Customer avatar
, Plumbing/Heating Engineer
0out of 0found this question helpful.
Was this helpful?Yes0No0


The rubber bungs that are supplied with the manifold will accommodate 32mm & 40mm waste pipe and can be cut at the markers to accommodate 50mm waste pipe.
23 May 2016
0of 0found this answer helpful.
Was this helpful?Yes0No0
1 of 1
  • 2016-05-27 T10:36:53.106-05:00
  • bvseo_lps, prod_bvqa, vn_prr_5.6
  • cp-1, bvpage1
  • co_hasquestionsanswers
  • loc_en_US, sid_22367, prod, sort_default
1 of 1
Brand FloPlast
Colour Grey
Connection Type Push-Fit
Manufacturer Guarantee 1 years
Manufacturing Standards BS4514: 2000
Model No SP558G
Pack Size 1
Pieces in Pack/Case 1
Product Depth 210 mm
Product Height 217 mm
Product Type Waste Manifold
Product Width 268 mm
Total Product Weight 1.156 kg