Browse store

Scheppach HS80 210mm Tilt Arbor Table Saw 240V (44937)

Lightweight, economical and portable table saw. Torsion-resistant steel construction. Features duplex saw blade height and angle adjustment. No-volt safety release switch provides safety in use. Ideal for those with a limited workshop space, or just need a lightweight portable table saw to carry to where the work is. Supplied with extending panel support table, push stick, mitre guide, rip fence, saw blade and carbon brushes.

  • 1200W Brush Motor
  • Max. Cut Depth: 48mm
  • 20-Tooth TCT Blade Included
  • Aluminium Table
  • Parallel & Mitre Fences
  • Dust Extraction Facility
  • Constant Speed Under Load
  • Blade Brake
  • Telescopic Left Table Extensions

More Info

£109.99INC VAT

Add to basket for...

Not available to Click & Collect

Store Collection Unavailable

Scheppach HS80 210mm Tilt Arbor Table Saw 240V is rated 3.4 out of 5 by 12.
  • y_2017, m_2, d_27, h_2
  • bvseo_bulk, prod_bvrr, vn_bulk_0.0
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_12
  • loc_en_GB, sid_44937, prod, sort_[SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix

Add to saved list...

Save
Rated 1 out of 5 by from Poor quality build, inaccurate This saw has two major faults: (1) Firstly, the table itself is not even close to being flat and is about 2mm lower in the middle than around the outside. This was glaringly obvious by eye, but just to make sure I measured it by placing a steel rule across the top. (2) The table extension that slides in and out on the left hand side is not flush with the table, and is 2-3 mm higher at the front than at the back. Both of these faults mean that the saw will never cut remotely accurately especially when doing mitre cuts. The overall build is very poor and the manufacturer's QA is clearly lacking, so I would say save your money and avoid this tool.
Date published: 2016-12-19
Rated 5 out of 5 by from great value saw great saw for the money ideal purchess for what im going to use it for with many features often seen on more expensive machines
Date published: 2016-10-21
Rated 4 out of 5 by from really good saw this is a really good saw, but why was it supplied with the wrong plag on the power lead, had to double check the power rating on the motor, then fit another plug, easy to set up, i have fitted it to an old saw base with legs on it, would reccommend
Date published: 2016-09-09
Rated 5 out of 5 by from Value for money table saw Saw this as the Deal of the Day and it filled the bill exactly - plenty of features, some only available on more expensive units. Ideal for my purpose. Haven't used it that much, so far so good.
Date published: 2016-01-15
  • y_2017, m_2, d_27, h_2
  • bvseo_bulk, prod_bvrr, vn_bulk_0.0
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_12
  • loc_en_GB, sid_44937, prod, sort_[SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix

I'd like to replace the mitre gauge, can you tell me the slot (track) size?

Asked by: Cadmanuk
HI The mitre guide slot on the hs 80 is approx 21mm wide and 13mm deep , the table top is fabricated steel .
Answered by: Scheppach-Expert
Date published: 2017-01-25

Guide fence

Does the guide fence lock at both ends of the machine?
Asked by: Wdevaal
Hello The rip fence does lock at both the front and the back of the saw table by means of clamps and turn knobs .There is also a scale at both front and back .
Answered by: Scheppach-Expert
Date published: 2017-02-12

Does this come with a pipe for the dust extraction facility?

If not can one be purchased? And then can this be hooked up to a normal hoover such as a Henry?
Asked by: Ginger83
Good morning .the machine does not not.but an extractor such as sku (sfx part number ) 31896 will have everything you need to connect the 2 together in a safe manner . this will give you the best extraction facility for your saw kind regards scheppach
Answered by: Scheppach-Expert
Date published: 2017-01-15

Are there saw blades which will give a neat cut (more teeth) which are compatible with this saw?

Is it just normal circular saw blades which can be used with this or special saw blades?
Asked by: Ginger83
Hello The saw blade specification is 210mm x 30mm bore x 2.6mm kerf ( width of tooth ) there are blades available with 24 , 48 and 60 teeth off the shelf .
Answered by: Scheppach-Expert
Date published: 2017-01-08

How far to the right does the guide allow? and is there an extension that can be purchased to the right if it is needed?

Asked by: Ginger83
Hello The ripping width is 120mm to the right , there is an extension to the left hand side making it possible to rip 385mm , there is no rh extension .
Answered by: Scheppach-Expert
Date published: 2017-01-08
  • y_2017, m_2, d_26, h_20CST
  • bvseo_bulk, prod_bvqa, vn_bulk_0.0
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_14
  • loc_en_GB, sid_44937, prod, sort_[SortEntry(order=LOCALE, direction=DESCENDING), SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix
Specification
Blade Description TCT Blade Included
Blade Diameter 210 mm
Brand Scheppach
Colour Blue / Grey
Corded or Cordless Corded
Cutting Depth Capacity 48 mm
Disc Bore Size 30 mm
Manufacturer Guarantee 2 Year Manufacturer's Guarantee (T&Cs Apply)
Model No HS80
No Load Speed 4800 rpm
Number of Teeth 20
Pack Size 1
Pieces in Pack/Case 1
Power Output (Watts/Kw) 1200 W
Power Voltage Supply 240 V
Product Height 435 mm
Product Length 470 mm
Product Type Tilt Arbor Table Saw
Product Width 575 mm
Total Product Weight 16 kg

Disc dia. 210 x 30mm bore. W x L x H: 575 x 470 x 435mm. Table W x L: 525 x 400mm. Max. cutting depth at 90°: . No. load speed: 4800rpm. Weight: 16kg. Bevel capacity 0-45°. Cutting depth capacity at 90°: 48mm, at 45°: 45mm. Includes Plug.

Product contents

HS80, blade guard, push stick, longitudinal stop, stop bar, rip fence, saw blade, blade key and flange key.

Downloads

Instruction Manual

*Delivered direct from our suppliers in the number of working days stated on the delivery button