Browse store

Makita 6843 / 2 Auto-Feed Screwdriver 240V (72415)

Accepts screws up to 55mm long. Includes screw guide and integral belt clip. Supplied with carry case and Phillips bit.

  • Uses 25-55mm Collated Screws
  • Depth Adjustment
  • Variable Speed & Reverse
  • Anti-Slip Nose
  • Soft-Grip Handle

More Info

£279.99INC VAT

Add to basket for...

Not available for delivery
Rated 3.8 out of 5 by 5 reviewers.
  • 2016-10-22 T09:00:50.420-05:00
  • bvseo_lps, prod_bvrr, vn_prr_5.6
  • cp-1, bvpage1
  • co_hasreviews, tv_5, tr_5
  • loc_en_US, sid_72415, prod, sort_default

Add to saved list...

Rated 4 out of 5 by Top screw gun Easy to load & use . Makes fixing plasterboard a pleasure 9 Apr 2016
Rated 5 out of 5 by auto feed screwdriver240v Doing a loft conversion and I was told that this tool would speed up the job, when it come to put the plaster boards on. It was brilliant, it cut the job time down in half. No more trying to hold a screw and the cordless drill when putting up plaster boards , just push the auto feed screw driver against the board hand it's as simple as that . 5 Apr 2016
Rated 1 out of 5 by makita autofeed Don't buy, don't buy, they keep jamming all the time and are pure rubbish took back for a refund asap,remember don't buy this autofeed driver 19 Nov 2013
Rated 4 out of 5 by Great for fast floor fixing! I bought one of these last year and used it to fix a very large area of chipboard flooring in a big master bedroom. I've also just finished boarding out the loft with it (and have plans for future use). I reckon I used about 600 screws for the bedroom and am SO glad I didn't have to set them manually. With this little guy, you simply pull the trigger, then point and push. A real time-saver and, when used correctly, results in a good, strong fixing. Once you're used to it, you can even keep the motor running and simply move along a row of boards (for example), just pushing down as you go. I think this really is a great tool, only let down by issue 5, below (and that, hopefully, will be dealt with in the future). A few points to note: 1) Don't be shy or go at it half-hearted. Push firmly and smoothly until the screw is fixed. If you ease off part way through, the driver bit will chatter against the screw-head resulting in a) a poor fixing and b) massively increased bit-wear. 2) This tool will allow you to fix flooring fairly close to a wall (for example) but is quite long, so not suitable for tight spaces such as under in the eaves of your loft. That said, it still took the bulk of the pain out of fixing our loft boarding. 3) Whilst you can use it very slightly off 90 degrees, it's best to keep it as near perpendicular as possible. Otherwise, the screw-head may not end up flush AND you'll be increasing the bit-wear as the screw will stop while the bit's still spinning in it (horrible noise!!). 4) I used Floor-Fix collated screws (Quote No: 50954), which are nice because of their 'anti-jacking' feaature. However, they require Pozi-2 bits, rather than the Philips#2 that are supplied with the unit. Check you have the right bits for the right screws!! 5) Replacement driver bits are not especially cheap or easily come by! Until I became practiced at using this driver, I managed to inflict quite a lot of wear on the bits (I wore 2 out!!). Prices seem to vary between £12 & £18 for three, PLUS they don't appear to be in ready-supply. Makita make a wide range of bit sizes (these are 157mm) and most distributors don't seem to stock the entire range, so have to order them in. THIS is why the 6843 didn't score well for me on the 'Value' and, thus, 'Overall' ratings. So, if you're a novice (& likely wear out bits, like me) and have a lot of screws to fix, I'd recommend getting a small stock in BEFORE starting work. You don't want to be sitting there with 200 quids' worth of driver and a 1000 collated screws all ready to go, and then find you've suddenly no means of driving them ;-) Surprisingly, Screwfix don't currently (as at April, 2009) supply replacement bits. However, after I suggested it would be sensible to stock the consumables for the products they sell, they agreed and have passed this onto the team responsible for deciding what goes in the Screwfix catalogue. Maybe, by the time anyone reads this, these parts will be in stock - go check... Hope this helps anyone thinking of buying. 16 Apr 2009
  • 2016-10-22 T09:00:50.420-05:00
  • bvseo_lps, prod_bvrr, vn_prr_5.6
  • cp-1, bvpage1
  • co_hasreviews, tv_5, tr_5
  • loc_en_US, sid_72415, prod, sort_default
Page : 2 next>
Brand Makita
Carry Case/Bag Included Yes
Corded or Cordless Corded
Manufacturer Guarantee 1 Year Guarantee
Model No 6843 / 2
Pack Size 1
Pieces in Pack/Case 1
Power Output (Watts/Kw) 470 W
Power Voltage Supply 240 V
Product Type Auto-Feed Screwdriver
Total Product Weight 2 kg

Max. screw dia. 4mm. Weight 2kg. 110V version includes plug.


Instruction Manual