Browse store

Fischer FIP 300SF Polyester Styrene-Free Resin 300ml (23386)

300ml. Low odour, 2-component resin for general fixing under dry conditions. Mixes automatically via the static mixer nozzle. Uses standard sealant gun.

More Info

Bulk saving available

Qty Price per item
1 - 4 £10.99 (£36.63/Ltr)
5 + £9.89 (£32.97/Ltr)
£10.99INC VAT (£36.63/Ltr)

Add to basket for...

Fischer FIP 300SF Polyester Styrene-Free Resin 300ml is rated 4.6 out of 5 by 29.
  • y_2017, m_3, d_25, h_24
  • bvseo_bulk, prod_bvrr, vn_bulk_1.0.0
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_29
  • loc_en_GB, sid_23386, prod, sort_[SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix

Add to saved list...

Save
Rated 4 out of 5 by from Does a job Used to secure fixing in old brick wall. Did the job but only used 1/3rd of tube. No way to save the rest for another job so threw away 2/3rds of tube. Would give 5 stars if it cam with spare mixer tube and cap.
Date published: 2017-02-02
Rated 5 out of 5 by from Amazing product! Had a curtain rail to put up - the middle bracket was a nightmare because the plasterboard had been over-drilled. My sds drill made a good job of getting holes in the lintel but the rawlplugds still wouldn't bite - this product came to the rescue. Easy to squirt in and after an hour it was rock hard. I used goggles and gloves but actually not messy to use. The only issue is how to get new nozzles for the next time I need to use it.
Date published: 2017-01-28
Rated 5 out of 5 by from Really useful resin This stuff is so easy to use. 300ml size lets you use a standard skeleton gun and doesn't waste material. Other reviewers have covered use of spare nozzles and replacing the cover cap to keep it fresh. However, some advice that it "sets hard" in 15 minutes may mislead you. It does set firm but the online technical data does say it "fully cures" in x-hours and is temperature dependent - the colder it is the slower it cures. So dont fully tighten up or load the fixture without attention to this. Follow the instructions and it will repay you with its high reliability
Date published: 2017-01-21
Rated 5 out of 5 by from Well Hard ! Does what it says on the tube,great stuff. Be aware when you use it one with the nozzle that's it used up can't use the nozzle again. But you can buy replacements if you have some to use in the tube as long as the top is screwed on tight.
Date published: 2016-12-14
  • y_2017, m_3, d_25, h_24
  • bvseo_bulk, prod_bvrr, vn_bulk_1.0.0
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_29
  • loc_en_GB, sid_23386, prod, sort_[SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix

outdoor

hi is this suitable for outdoor use and what temperatures. also is it good to use to repair crack concrete? thanks
Asked by: amii
FIP 300 SF is not a crack repair product. It is to be used with the substrate above 5°C and preferably in a dry area.
Answered by: fischertech
Date published: 2017-01-30

plastic wall plug

can you use standard wall plug with this? and can you put the screw in after it sets.
Asked by: amii
This method is unorthodox but I do not see why it should not work. I don't think you will be able to put the screw in whilst it is still wet, it will spin. Make sure the drill hole is 2mm bigger than the Ø of the plug. Regards Technical
Answered by: fischertech
Date published: 2017-03-12

plastic wall plug

can you use this with a plastic wall plug, so to put the resin in the hole and put a wall plug in there and let it set or do you have to put the screw in before it sets.
Asked by: amii
Thanks for your enquiry , This method is unorthodox but I do not see why it should not work. I don't think you will be able to put the screw in whilst it is still wet, it will spin. Make sure the drill hole is 2mm bigger than the Ø of the plug. regards Technical
Answered by: fischertech
Date published: 2017-03-12

Would this be suitable for drilling into to attach sleeve anchors for a TV wall hanging bracket (after cleaning out crumbly mortar area - bracket needs to be in very specific spot)?

Asked by: Gingamonkey
It would be better to install a threaded rod into the wet resin to attach your bracket rather than to use it as a filler. Make sure your drill hole is thoroughly cleaned out with a brush and blowout pump before injecting resin. You will need a 12mm Ø drill hole for anM10 threaded rod. Regards Technical.
Answered by: fischertech
Date published: 2017-03-12

Fire rating?

im hoping to use this to fix a floating mantle shelf into a brick chimney. (oak shelf). the fire will be solid fuel, so can you advise if this product has a suitable fire rating / operating capability?
Asked by: JC16
This is a general purpose resin and will have no data regarding fire rating. Temperature will be 40° max If you switch to FIS VT 380 C it has a long term max temperature of 72°C
Answered by: fischertech
Date published: 2017-03-12
  • y_2017, m_3, d_24, h_17CST
  • bvseo_bulk, prod_bvqa, vn_bulk_1.0.0
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_10
  • loc_en_GB, sid_23386, prod, sort_[SortEntry(order=LOCALE, direction=DESCENDING), SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix
Specification
Brand Fischer
Manufacturer Guarantee 1 Year Guarantee
Model No FIP 300SF
Pack Size 1
Pieces in Pack/Case 1
Product Type Polyester Styrene-Free Resin
Sealant Adhesive Volume 300 ml

Downloads

Instruction Manual

Safety Data Sheet (COSHH)