Browse store

Danfoss FP715si Programmer (63760)

Independent timing. 5-wire installation. Override facility. Holiday mode. Automatic BST/GMT time change. Boost function. EN 60730-2-7.

  • 24 Hour, 5 / 2 Day or 7 Day Programmable
  • 3 Pre-Set Programmes
  • Digital Display
  • 2 or 3 On/Off Periods per Day
  • Suitable for Gravity-Fed & Fully Pumped Systems
  • 5 Wire Installation
  • Backlit Display
  • Battery Back-Up
  • Energy Saving Trust Approved
  • 1 Year Guarantee

More Info

£66.99INC VAT

Add to basket for...

Danfoss FP715si Programmer is rated 4.0 out of 5 by 16.
  • y_2017, m_9, d_18, h_22
  • bvseo_bulk, prod_bvrr, vn_bulk_2.0.3
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_16
  • loc_en_GB, sid_63760, prod, sort_[SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix

Add to saved list...

Save
Rated 4 out of 5 by from Great 5-wire programmer I needed an urgent replacement for a very old 5-wire programmer that got "bashed". Not many 5-wire units around - I didn't want to do any re-wiring and the Local Screwfix had this in stock. Only slight problem was that the wiring on my old one was on the right whilst this has the wiring on the left end. Luckily the wires were not tight and pulled sufficient through to fit it in 20 minutes . Easy Straight wire for wire replacement. very easy to programme. Does just what we want
Date published: 2017-08-31
Rated 5 out of 5 by from Easy to use, trade choice Very easy to use/user friendly. I wire up a lot of heating systems for local plumbers using this product, never any problems, it's a good well made product.
Date published: 2017-08-17
Rated 4 out of 5 by from Nice unit. I have fitted a few of these units over the years, reliable, 5 wire, easy installation, fully recommended and good price.
Date published: 2016-01-21
Rated 4 out of 5 by from Just the job! Got this to replace an old timer that had failed on an even older boiler. The old one had a compatible baseplate, so all I had to do was set the Danfoss to a gravity fed system and 5/2 day schedule, and it plugged straight in - except the Danfosss intrudes slightly into the space within the backplate a little, so I had to rearrange the wiring I had there to allow it to fit. Not difficult to do though, then I just set the programming to my requirements and away it went. Too early to say how it is for reliability, but for the prices, I would expect to get a good number of years out of it.
Date published: 2015-12-01
  • y_2017, m_9, d_18, h_22
  • bvseo_bulk, prod_bvrr, vn_bulk_2.0.3
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_16
  • loc_en_GB, sid_63760, prod, sort_[SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix

can this unit replace the danfoss set2e unit without having to place backplate?

Asked by: markm122
The FP715si has a different wall plate to the SET 2E . you can use the FP715si to replace the SET2E but you would have to replace the wall plate. The SET2E is still manufactured.
Answered by: Danfoss Product Expert
Date published: 2017-07-29

Is the FP 715si a direct replacement for the FP 75

Can you simply unplug the Danfoss FP75 and replace with the Danfoss FP715si without altering the wiring thanks.
Asked by: Earlofh
good afternoon, yes the FP715si is the latest plug in replacement for the FP75,
Answered by: Danfoss Product Expert
Date published: 2017-07-29

Will this unit replace a Randall 922 with regard to functionality, and will it fit the same backplate?

Asked by: MANHydeng
The 922 is a similar product but does not have a common backplate.
Answered by: Danfoss Product Expert
Date published: 2017-04-22

Could this be used as a direct replacement for a TP9000?

Asked by: H2R1000
Hi, the TP9000 is a programmable room thermostat with a hot water channel, we have a direct replacement in the form of the TPOne-M. The FP715Si is purely a two channel programmer and has no integral thermostat.
Answered by: Danfoss Product Expert
Date published: 2017-04-22

How about temperature sensors, included?

Asked by: Mont
This is a programmer, for temperature control you would need one of the Danfoss TP ranges, these are programmable room thermostats. or to work in conjunction with the FP715, an RET1000 or RET2000 room thermostat would be recommended.
Answered by: Danfoss Product Expert
Date published: 2017-04-22
  • y_2017, m_9, d_18, h_22CST
  • bvseo_bulk, prod_bvqa, vn_bulk_2.0.3
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_14
  • loc_en_GB, sid_63760, prod, sort_[SortEntry(order=LOCALE, direction=DESCENDING), SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix
Specification
Brand Danfoss
Central Heating Control Type Programmers
Compatible Boiler Type All Boilers
Display Type Digital Display
Installation Type 5-Wire Installation
Manufacturer Guarantee 1 Year Guarantee
Model No FP715si
Pack Size 1
Pieces in Pack/Case 1
Product Depth 32 mm
Product Height 88 mm
Product Type Programmer
Product Width 135 mm
Programme Facility 7 Day, 5/2 Day or 24 Hour Programmable
Suitable System Suitable for Gravity-Fed & Fully-Pumped Systems
Zoning Level Up to Two

Switching/contact rating: 3(1)A. H x W x D: 88 x 135 x 32mm. Backplate fit: British Gas Standard. Suitable for underfloor heating.

Downloads

Instruction Manual