Browse store

Opella Bottom Entry Toilet Cistern Ball Valve Part 3 (52836)

Arm adjustable from 170mm to 240mm.

More Info

Bulk Save Save up to 10%

QTY Price per item Saving
1 - 2 £4.59 -
3 + £4.13 Save 10%
£4.59INC VAT

Add to basket for...

Opella Bottom Entry Toilet Cistern Ball Valve Part 3 is rated 4.2 out of 5 by 118.
  • y_2017, m_5, d_25, h_3
  • bvseo_bulk, prod_bvrr, vn_bulk_1.0.0-hotfix-1
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_118
  • loc_en_GB, sid_52836, prod, sort_[SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix

Add to saved list...

Save
Rated 4 out of 5 by from Good, but fragile. The first one was broken where the float arm joins the valve. I don't recall breaking it. It was only as I filled the cistern did I realise the small plastic tab was broken. I have to assume I broke it as I fitted it, but if I did it was with minimal force. Second one was fitted with great care and works just fine.
Date published: 2017-04-20
Rated 5 out of 5 by from Easy install I am a D I Y person and I found this product easy to install and it served as an easy fix for a previous faulty water valve. Hopefully this will last until I decide to change the toilet .
Date published: 2017-04-12
Rated 5 out of 5 by from Good value direct replacement Simple to fit as a direct replacement for the broken one. Will see how long it lasts but no concerns. Usual great service from screwfix who has it in stock
Date published: 2017-04-11
Rated 1 out of 5 by from Beware! Fitted this valve fairly easily, but turned the system on and it turns out the valve had no internals! Had to remove it and replace old one again, so back to square one. If you do buy this product, check the valve internals are there before fitting it!
Date published: 2017-04-06
  • y_2017, m_5, d_25, h_3
  • bvseo_bulk, prod_bvrr, vn_bulk_1.0.0-hotfix-1
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_118
  • loc_en_GB, sid_52836, prod, sort_[SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix

What is the thread size?

Asked by: Dragonfire709

Mounting Opella ball valve

The rubber washer at the base of the unit, does it go inside or outside of the cistern casing?
Asked by: MrRyan

What height is it?

Asked by: Keith100

Does this come with the floating ball attached to the end, just its not attached in the picture

Asked by: Rowe
No, it does not. And don't try to use the Float Ball (76297) that Screwfix show on the same page as this valve. The threaded part of the Ball isn't long enough to allow the Ball to be screwed up tight enough to clamp the Ball at an angle to the bar. Hence the Ball wanders all over the bit and jams against the cistern wall. Stopping the valve from completely closing. I guess you could hacksaw a bit off the length of the stud on the arm. But it's a bit of a bodge and shouldn't be necessary.
Answered by: CRBt
Date published: 2017-05-12

Does it work with low pressure from a cold water tank?

Asked by: Stirlingman
  • y_2017, m_5, d_24, h_21CST
  • bvseo_bulk, prod_bvqa, vn_bulk_1.0.0-hotfix-1
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_6
  • loc_en_GB, sid_52836, prod, sort_[SortEntry(order=LOCALE, direction=DESCENDING), SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix
Specification
Brand Opella
Manufacturer Guarantee 1 Year Guarantee
Pack Size 1
Pieces in Pack/Case 1
Product Type Bottom Entry Toilet Cistern Ball Valve
Toilet Fitting Type Ball & Float Valves

Arm length: 170-240mm.