Browse store

LAP Standalone PIR 140° (11291)

Polycarbonate.

  • IP44
  • 12m Detection Range
  • Adjustable Dusk-to-Dawn Sensor
  • Adjustable Time On
  • Manual Override
  • Pan & Tilt

More Info

£10.49INC VAT

Add to basket for...

LAP Standalone PIR 140° is rated 4.4 out of 5 by 138.
  • y_2017, m_6, d_23, h_24
  • bvseo_bulk, prod_bvrr, vn_bulk_1.0.0-hotfix-1
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_138
  • loc_en_GB, sid_11291, prod, sort_[SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix

Add to saved list...

Save
Rated 5 out of 5 by from 1 failure in 200, enough said. about 200 fitted in last few years, 1 callback in all that time. unbeatable. *****
Date published: 2017-02-24
Rated 5 out of 5 by from It puts light on the subject After many years of use, my original PIR finally gave up. This PIR replacent was very easy to retrofit and set up Great value for money Highly recommended
Date published: 2017-02-23
Rated 4 out of 5 by from Good value product Good value and simple to install and set up. Bought to replace an identical one installed about 15yrs ago so I'm hopeful that this will last as long.
Date published: 2017-02-17
Rated 2 out of 5 by from Ok but not great I bought this to control some lights to illuminate my garden path, my initial reaction on opening the box was pretty good, wiring up wasn't a problem, set the unit at 2metres as instructed, I found the cover catches were a little weak but do the job, the reason I gave it a lower rating is the range, I'm not sure where the 12metres comes from but I can almost touch the sensor before lights come on, the range nearer 12ft rather than 12meters. Unfortunately I'm well up the garden path long before the lights switch on. Ok but not great.
Date published: 2017-02-12
  • y_2017, m_6, d_23, h_24
  • bvseo_bulk, prod_bvrr, vn_bulk_1.0.0-hotfix-1
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_138
  • loc_en_GB, sid_11291, prod, sort_[SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix

Product info

Few Qs please Do we have to link this light to a mains? Is there a switch so we can keep it on eg for 2 hours if needed? Is there a switch to turn it off if its not needed? Also, how easy is it to fit it? Do I need to link it anything at all?
Asked by: Alpa
Hello Alpa, The PIR has to be connected to mains. It can be set to keep a light on from 5 seconds to 5 minutes. This can be wired to a switch so that once turned "On" any motion picked up will activate it. If set to the "Off" position the PIR will not function. For installation enquiries we recommend you contact a qualified tradesperson for advice. Thank you for using Q and A, EC.
Answered by: Chubbtonk
Date published: 2017-05-29

To wire this to an existing light is the feed wire fed into the lamp first and then connected to the pir or into the pir first and then to the lamp

Asked by: Ficky
Hello Ficky, Every installation is different due to the varying circumstances of the site and environment. Therefore we advise that you contact a local tradesperson who will be able to view and assess your particular requirements. They will be able to provide further advice for the installation of the PIR. Thank you for using Q&A.
Answered by: jboon
Date published: 2017-06-20

I am connecting to unearthed LED light fittings, the Sensor will be earthed iaw the wiring diagram, I presume the PIR sensor will still function even though no earth from the LEDs, Am I correct?

Asked by: JFRT
Hello JFRT. As long as the standalone PIR is wired correct there is no problem connecting a Live and Neutral to your light. Thank you for using Q&A, [BH].
Answered by: yeldarb
Date published: 2017-03-01

What is the minimum wattage for this product.

Most of these sensors need a minimum current draw to operate. We have some 10 year old similar sensors and when you put a LED bulb in it just flashes. I would like to replace to start using LEDs.
Asked by: TimCW
Hello TimCW, This product can be used with; 1000W incandescent, 500W fluorescent and a 50W LED equivalent. When changing to LED's you may also require LED Drivers, however this would need to be confirmed with a suitably qualified tradesperson. Thank you for using Q&A.
Answered by: LMac
Date published: 2017-06-03

PIR SENSOR

does this product need to be earth
Asked by: STEDMONDS
Hello, Please see the following extract from the instructions. Hope that helps: Connect the mains supply cable to the terminal block on the unit as follows (see connection diagram): NEUTRAL (Blue) N EARTH (Green/Yellow) LIVE (Brown) L Connect the cable from the lighting load to the terminal block on the unit as follows (see connection diagram): NEUTRAL (Blue) N EARTH (Green/Yellow) LIVE (White) L’
Answered by: marchington
Date published: 2017-05-27
  • y_2017, m_6, d_23, h_5CST
  • bvseo_bulk, prod_bvqa, vn_bulk_1.0.0-hotfix-1
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_13
  • loc_en_GB, sid_11291, prod, sort_[SortEntry(order=LOCALE, direction=DESCENDING), SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix
Specification
Adjustable Adjustable Pan & Tilt
Brand LAP
Colour Black
Construction Material (Lighting) Polycarbonate
Fixings Supplied Fixings Supplied
IP Rating IP44
Manufacturer Guarantee 1 Year Guarantee
Model No IQ-140-B
Pack Size 1
Pieces in Pack/Case 1
PIR PIR
Power Voltage Supply 230 V
Product Depth 105 mm
Product Height 170 mm
Product Type Standalone PIR
Product Width 65 mm
Total Product Weight 0.22 kg

W x D x H: 65 x 105 x 170mm. 230V. 50Hz. IP44. Switching capacity: 1000W incandescent and 500W fluorescent. Fixings Supplied.

Downloads

Instruction Manual