Browse store

Halolite LED Constant Voltage Driver 1-16W (85503)

Polycarbonate. Loop-in. Loop-out. Not pre-wired. SELV.

  • IP20
  • Short Circuit Protection
  • Overload Protection
  • Leading Edge
  • Max. Ambient Temperature: 50°C
  • Max. Case Temperature: 75°C

More Info

£17.99INC VAT

Add to basket for...

Halolite LED Constant Voltage Driver 1-16W is rated 3.5 out of 5 by 19.
  • y_2017, m_7, d_25, h_12
  • bvseo_bulk, prod_bvrr, vn_bulk_1.0.0-hotfix-1
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_19
  • loc_en_GB, sid_85503, prod, sort_[SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix

Add to saved list...

Save
Rated 1 out of 5 by from Disappointing I bought this unit to power 5 of Screwfix's 2.9w MR16 downlighters (ie 14.5w total). It could not drive them despite a claimed 16w capacity. When i tried 4 bulbs (ie 11.6w) it improved, but was still very hit and miss. Symptoms - lights flash rapidly on and off - which I've read is its over-current mode. I read that sometimes AC transformers can be used with LED's (god know how!). I tried one and it dd not. But the second one I tried of a different make/model worked perfectly. So my advice, if you have some old AC units, try those first - you might save yourself some money!
Date published: 2017-06-02
Rated 1 out of 5 by from didn't work I tried two of these, the first one lasted about two weeks then made the bulbs flash, it got worse of the next few weeks, i took it back and replaced it with a new one, that was the same...
Date published: 2017-03-25
Rated 1 out of 5 by from Didn't work Wouldn't run 3 x 5w led MR16 bulbs. This transformer has three separate led outputs. Wired transformer in parallel as per instructions to get single +/- output which in itself was a pain as terminals are very small with little space for wires. After going through this time consuming process, it then only had sufficient output for one 5w bulb. Add a second and cut out switches in. Add a third and it flashes repeatedly. Returned to store and bought a new transformer from an online led light retailer which took two minutes to fit and worked perfectly out of the box.
Date published: 2017-02-21
Rated 3 out of 5 by from Can't drive 3 x 5w LED's Used with 3 x LAP LED MR16's, and all lamps flashed. Took one of the MR 16's out of circuit, all ok, though ran a bit warm. So although it is rated as 16w it couldn't drive 15w. I returned it and got a 24w driver cheaper elsewhere, that worked ok.
Date published: 2016-08-31
  • y_2017, m_7, d_25, h_12
  • bvseo_bulk, prod_bvrr, vn_bulk_1.0.0-hotfix-1
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_19
  • loc_en_GB, sid_85503, prod, sort_[SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix

Purchased this driver some 12 months ago and the unit has been happily powering 5 x 1.4 watt LED’s.Decided to fit 5 x LAP MR16 LED Lamp GU5.3 346lm, 5 watt (4698G). Swopped a lamp at a time then with a third one connected, rapid flickering commenced.

Asked by: Solihullspark
The driver is only rated up to 16 watts. The previous load you had was 7 watts. The new load is going to be 25 watts well over the drivers rating so I imagine when you put the 3rd lamp in it hit the limit and started to flash with the overload. You would either need to buy another driver capable of coping with the new load or split the load between 2 or maybe 3 of this type of driver.
Answered by: sparkydave7
Date published: 2017-05-21

Is this Driver compatible?

Old (broken) driver is a Constant Voltage, 240VAC, 50Hz input and 12VDC, 0.5A output with max load 5W. Will your product (HALOLITE LED CONSTANT VOLTAGE DRIVER 1-16W [85503] ) be ok as a substitute even with the current output being slightly higher?
Asked by: Markyy
Yes that driver should be a suitable alliterative. Thanks
Answered by: Aurora Technical
Date published: 2017-06-17

My lights flash when switched on

I have connected 3 x 5w led lamps from 1 output in parallel not sure if polarity is right?
Asked by: steve2sail
I have the same problem. Bought 3x5w LAP MR16 bulbs to go with this and they always flash. If I only fit one bulb it flashes when connected either way round. Wish I'd read this before purchasing as I probably wouldn't have bothered and saved myself 2 visits to the store.
Answered by: NBPhil
Date published: 2017-06-06

do i need one of these per downlighter?

Asked by: brian1969
  • y_2017, m_7, d_25, h_24CST
  • bvseo_bulk, prod_bvqa, vn_bulk_1.0.0-hotfix-1
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_4
  • loc_en_GB, sid_85503, prod, sort_[SortEntry(order=LOCALE, direction=DESCENDING), SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix
Specification
Brand Halolite
Current Type DC
Dimmable Non-Dimmable
IP Rating IP20
Manufacturer Guarantee 3 Year Manufacturer's Guarantee (T&Cs Apply)
Manufacturing Standards EN 55015, EN 61000, EN 61547, EN 61347
Max. Case Temperature 75 °C
Model No HA-LED16T
Overload Protection Overload Protection
Pack Size 1
Pieces in Pack/Case 1
Power Output (Watts/Kw) 1-16 W
Power Voltage Supply 12-240 V
Product Depth 24 mm
Product Height 24 mm
Product Length 155 mm
Product Type LED Constant Voltage Driver
Product Width 38 mm
Short Circuit Protection Short Circuit Protection
Total Product Weight 0.095 kg

W x D x H: 38 x 24 x 24mm. DC. 0.07A current. 1-16VA. 12-240V. Min dimmable load 35W. Non-dimmable.

Downloads

Instruction Manual