Browse store

Drayton Zone Replacement Valve Actuator (76959)

Manual lever and valve position indicator. Simple industry standard wiring. Conforms to EN 60730.

  • Energy Saving Control
  • Easy Snap-On Installation
  • 5-Wire Cable

More Info

£44.49INC VAT

Add to basket for...

Drayton Zone Replacement Valve Actuator is rated 4.4 out of 5 by 14.
  • y_2017, m_3, d_24, h_18
  • bvseo_bulk, prod_bvrr, vn_bulk_1.0.0
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_14
  • loc_en_GB, sid_76959, prod, sort_[SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix

Add to saved list...

Save
Rated 5 out of 5 by from Excellent product This product was easy to install works very well fixed my heating problem very pleased would recommend
Date published: 2017-02-22
Rated 5 out of 5 by from Drayton Zone Actuator Valve Have only just installed the unit and have not yet wired it into the connector strip, Have other Drayton central heating products installed and I am very happy with the product. They are well priced and work well. Have rated with three stars at this stage and will be in a better position to give a genuine rating once it is wire up and running.I have not doubt it will require a five star rating.
Date published: 2016-11-15
Rated 5 out of 5 by from Simple Easy to replace, although it would be great if the micro switch was available on its own - heating now working :-)
Date published: 2016-09-29
Rated 5 out of 5 by from Manufacturer's valve actuator Noticeably better price than a local competitor, manufacturer's own replacement, in stock, newish branch is closer - what more can you ask? Oh, and helpful staff.
Date published: 2016-06-01
  • y_2017, m_3, d_24, h_18
  • bvseo_bulk, prod_bvrr, vn_bulk_1.0.0
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_14
  • loc_en_GB, sid_76959, prod, sort_[SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix

Does this fit the old type drayton actuator ZA6, and do I have to drain the system before fitting?

My drayton valve actuator is about 12 years old.
Asked by: Ayiotis
The ZA6 is a detachable actuator that is released from the valve via a push button. If your valve has an actuator marked ZA6 has the push button release then they are compatible. It is not necessary to drain down the system tyo just change the actuator. If the existing valve has a bolted on actuator, the valve assembly will be obsolete and unsupported. The ZA6 will not attache to this valve. The system would require draining down and a replacement valve and actuator fitted as a replacement.
Answered by: Martin, Technical Support
Date published: 2017-02-16

Does this replacement head fit the 28mm body?

Asked by: Anonymous
This actuator will fit the 22mm and the 28mm valve bodies
Answered by: Martin, Technical Support
Date published: 2017-03-02

Drayton Zone Valve Actuator. My pump runs after heating and hot water has timed out or reached required temperature, would this suggest the micro switch has failed in the zone value actuator?

Asked by: Scooter1966
If it is the pump only that is running then this would suggest that the pump over run on the boiler is the issue. When the boiler shuts down the pump continues to run in order to dissipate the heat around the system. The pump should normally run for 5 minutes or so. If the pump is running and the boiler is fired up then this would suggest that the micro switch has failed.
Answered by: Martin, Technical Support
Date published: 2016-11-27

What would fault indications be

Central heating comes on when hot water should only be on, would this indicate faulty actuator. Regards Ian
Asked by: Buck52
Central heating coming on when the hot water only is being called for indicates that the Central Heating valve is open. This could be caused by a failed actuator not allowing the valve to close or a seized valve not allowing the actuator to close it or debris in the system which is not allowing the valve to close fully. Iwould advisehaving a heating engineer take a look at the system.
Answered by: Martin, Technical Support
Date published: 2016-09-10

hot water hot coming through valve spring does not move to reset when turning power off.

Asked by: oppi
This sounds as though the actuator or the valve have failed. Remove the actuator from the valve body by pressing in the release button on the side of the actuator. Test the valve spindle by turning it with your finger and thumb. If the valve spindle will not turn using just your finger and thumb or is stiff to turn then the valve body will require changing. Test the actuator by energising it and checking that it goes to position B - open. De-energise the valve and it should return to the A position – shut. If it does not do this then the actuator will require replacing.
Answered by: Martin, Technical Support
Date published: 2016-07-16
  • y_2017, m_3, d_24, h_23CST
  • bvseo_bulk, prod_bvqa, vn_bulk_1.0.0
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_7
  • loc_en_GB, sid_76959, prod, sort_[SortEntry(order=LOCALE, direction=DESCENDING), SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix
Specification
Brand Drayton
Installation Type Easy Snap-On Installation
Manufacturer Guarantee 1 Year Guarantee
Model No 27650SX
Pack Size 1
Pieces in Pack/Case 1
Power Output (Watts/Kw) 6.5 W
Power Voltage Supply 230 V
Product Type Zone Replacement Valve Actuator
Total Product Weight 1.32 kg

230V. 50Hz. 6.5W.