Browse store

JG Speedfit Valve & Tap Connector 15mm x ½ "mm (77333)

15mm x ½". BSP service valve tap connector.

  • Plastic

More Info

£9.89INC VAT

Add to basket for...

JG Speedfit Valve & Tap Connector 15mm x ½ "mm is rated 5.0 out of 5 by 3.
  • y_2017, m_10, d_21, h_22
  • bvseo_bulk, prod_bvrr, vn_bulk_2.0.3
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_3
  • loc_en_GB, sid_77333, prod, sort_[SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix

Add to saved list...

Save
Rated 5 out of 5 by from So easy!!! Bought this part to replace an old service valve on the cold water feed into the cistern of my toilet. The old valve had started to leak and due to the age I thought I'd replace rather than just swap the corroded gasket. This part was so easy to install, literally just push the fitting down onto the pipe. There's hardly any resistance and it clamps on tight. The universal screw thread on the opposite side fitted the fill valve on the cistern without problems and the fitting is water tight. These are slightly more expensive than the old compression/olive fittings but the expense is easily offset against the ease of installation and the quality of the fitting. I will be using more of these speedfit connections next time an opportunity arises. Couldn't ask for more.
Date published: 2017-10-16
Rated 5 out of 5 by from Excellent valve / JG Speedfit Purchased this valve to use on a bottom entry cistern. Works perfectly and looks good as well. The rubber seal is excellent , no need for PTFE or anything else for that matter , just hand tighten then 1/4 turn with grips. Note: Have given 5 stars for reliability but only fitted two days ago - I have purchased other JG Speedfit products and they have always been reliable , can`t see this product being any different.
Date published: 2016-02-11
Rated 5 out of 5 by from Too simple not to use Whenever I update the water feed I use these stop valves. They literally are a push fit and work equally well on copper or plastic piping. The valve always shuts off the water flow with no dribble. The best tool for turning the valve is a coin (probably 10p)
Date published: 2013-06-11
  • y_2017, m_10, d_21, h_22
  • bvseo_bulk, prod_bvrr, vn_bulk_2.0.3
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_3
  • loc_en_GB, sid_77333, prod, sort_[SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix

Mains Water Pressure.

I'm just checking, but will the handle mains water pressure for my cold tap?
Asked by: PatioCleaner
  • y_2017, m_10, d_21, h_22CST
  • bvseo_bulk, prod_bvqa, vn_bulk_2.0.3
  • cp_1, bvpage1
  • co_hasquestions, tq_1
  • loc_en_GB, sid_77333, prod, sort_[SortEntry(order=LOCALE, direction=DESCENDING), SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix
Specification
Brand JG Speedfit
Construction Material (Plumbing) Plastic
Manufacturer Guarantee 25 Year Manufacturer's Guarantee (T&Cs Apply)
Pack Size 1
Pieces in Pack/Case 1
Pieces in Pack/Case 1
Product Diameter 15 mm
Product Type Valve & Tap Connector