Blyss Wired Bell Push White (963HF)

£ 2.99INC VAT

Add to basket for...

Blyss Wired Bell Push White (963HF)

Wired illuminated bell bush. White finish.

  • Compatible with Blyss Doorbell Range
  • 2-Wire Installation

More Info

View all: Blyss Wired Door Bells

£2.99INC VAT

Add to basket for...

Add to saved list...

Rated 1 out of 5 by from 2 faulty ones Sadly had to of these faulty out of the box - neither one of them actually managed to go open circuit at any time, so completely useless as a door bell switch... After 2 wasted visits to the customer's home I ended up ordering a Byron branded bell push online - worked first time no problem!
Date published: 2021-07-04
Rated 4 out of 5 by from It is a doorbell Push Awkward screw terminals, but this is typical of all doorbell pushes (didn't help that the existing wires were stranded and entering from the side). Tucked wires under the metal connection plate, did not wrap around the screw (you can just prise the metal away from the plastic enough to slip wire in). It works! Time will tell if it is reliable! The Screwfix Pembroke Dock staff were very helpful
Date published: 2021-06-03
Rated 3 out of 5 by from BLYSS WIRED BELL PUSH W Collected within an hour of ordering. If the bell push was a little wider allowing the terminals to be slightly larger and further apart, would help. They are so close together you have to be careful that the bell wire does not impinge on both terminals, or on each other.
Date published: 2021-05-20
Rated 1 out of 5 by from Rubbish. Don’t waste your time Feels and looks cheap and nasty but that’s forgivable for the price. But the screw terminals are tiny and rubbish, and far too close together. There’s only a few MM between them so it’s nigh on impossible to screw the wires down without them touching each other, particularly since there’s no washer etc to hold the wire in place. And don’t touch this product if you have solid conductor doorbell wires (our 80s house does and I had to attach new lengths of stranded wire tails) as the screws won’t be sufficient to hold them in place, and there’s not enough space to wrap the wire around the screw. Finally got the wires in place only to find the doorbell wouldn’t latch itself onto the backing plate. When I looked they are the tiniest little nubs to keep the front on, could have been easily avoided with a small screw underneath or similar. Pulled it off and threw it straight in the bin. Don’t waste your time.
Date published: 2021-04-03
  • y_2021, m_7, d_25, h_19
  • bvseo_bulk, prod_bvrr, vn_bulk_3.0.18
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_15
  • loc_en_GB, sid_963HF, prod, sort_[SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix
  • bvseo_sdk, java_sdk, bvseo-4.0.0
  • CLOUD, getReviews, 16ms

whats the voltage range of the bulb in this bell pushh

Asked by: KeefyB
Hello KeefyB, The voltage range is 8-12 V Thank you for using Q&A
Answered by: Cwalm
Date published: 2021-03-17

Picture of the rear/inner workings

Screwfix can you post a picture of the rear of the product? I've noticed that another reviewer says there are separate terminals for wires to the light and the button - is this correct? A picture would help there.
Asked by: Iwanttoaskaquestion
Hello Iwanttoaskaquestion, If you would like a copy of the instruction manual please use the Contact Us form below: Thank you for using Q&A
Answered by: SWake
Date published: 2021-05-07

Illumination clour

Hi. Is the illumination colour blue as in the picture? Ive seen natural colour at other retailer. Thanks
Asked by: WAAM
Hello, Yes the illumination colour is a blue colour. Thanks for using Q&A. [DG].
Answered by: DGIFF
Date published: 2020-12-17

Is the light meant to stay on when wired to the mains?

Does the light stay on or is this wired incorrectly? The light currently goes off when the button is pressed, surely it should be the other way round?
Asked by: MadHatterSK3
Hello MadHatterSK3, The light is intended to stay on so that when it is dark it can help to with finding the bell push in the dark. Thank you for using Q&A SW
Answered by: SWake
Date published: 2020-12-22

Can this be used with battery powered bells or will it drain the batteries?

Asked by: Hubby21
Hello Hubby21, This can only be powered via the mains power supply. Thank you for using Screwfix Q and A. A.K.C.
Answered by: AliScrewfix1
Date published: 2020-04-30
  • y_2021, m_7, d_25, h_19CST
  • bvseo_bulk, prod_bvqa, vn_bulk_3.0.18
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_5
  • loc_en_GB, sid_963HF, prod, sort_[SortEntry(order=LOCALE, direction=DESCENDING), SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix
  • bvseo_sdk, java_sdk, bvseo-4.0.0
  • CLOUD, getReviews, 12ms
  • bvseo-msg: BV SEO Content for this product did not include verbose reviews.;
Brand Blyss
Colour White
Construction Material (Electrical) ABS Plastic
Doorbell Power Group Wired
Fixings Supplied Fixings Supplied
Manufacturer Guarantee 1 Year Guarantee
Pack Size 1
Parent Colour White
Pieces in Pack/Case 1
Power Voltage Supply 8-12 V
Product Depth 27 mm
Product Height 60 mm
Product Type Bell Push
Product Width 25 mm
Smart Compatibility Not Smart
Wireless/Wired Wired