Browse store

Titan TTB582PMP 400W Automatic Dirty Water Pump 240V (65041)

Clears dirty water including solids up to 18mm diameter from footings and ditches. Submersible. Also suitable for general duties. Supplied with a fitted RCD for added safety. Float switch turns the pump on and off automatically with changes to the water level. Not suitable for continuous use in fish ponds and fountains.

  • Pumps up to 150Ltr/min
  • 2 Year Manufacturer's Guarantee (T&Cs Apply)

More Info

£39.99INC VAT

Add to basket for...

Titan TTB582PMP 400W Automatic Dirty Water Pump 240V is rated 4.3 out of 5 by 147.
  • y_2017, m_2, d_25, h_2
  • bvseo_bulk, prod_bvrr, vn_bulk_0.0
  • cp_1, bvpage1
  • co_hasreviews, tv_1, tr_146
  • loc_en_GB, sid_65041, prod, sort_[SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix

Add to saved list...

Save
Rated 5 out of 5 by from Great Value Pump Used to empty the hot-tub, does it in quick time and good value
Date published: 2017-02-21
Rated 4 out of 5 by from Excellent value Really good pump cheaper than hire one for two day only bad point is buy the hose as a extra
Date published: 2017-02-11
Rated 4 out of 5 by from Wezzyman Does what it says on the tin. Excellent value for money.
Date published: 2017-01-01
Rated 3 out of 5 by from Clumsy float switch I bought the pump to evacuate waste water from a blocked drain. The pump sits in a temporary sump which is 33cm deep. The idea is that the pump should start working as soon as the sump starts filling - but it doesn't, as the float switch does not have enough boyancy to switch on in only 33cm. It needs nearly twice this depth for it to operate. I have got round the problem by adding extra buoyancy (corks) to the end of the switch. That said, when its starts pumping it clears the waste water effectively. If you need to operate in a relatively shallow area, then I would suggest buying a pump with a separate switch, which would give better control.
Date published: 2016-12-18
  • y_2017, m_2, d_25, h_2
  • bvseo_bulk, prod_bvrr, vn_bulk_0.0
  • cp_1, bvpage1
  • co_hasreviews, tv_1, tr_146
  • loc_en_GB, sid_65041, prod, sort_[SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix

How long is the Power lead??

Asked by: Peter313
Hello Peter313, the power lead is 10m thank you for using Q and A.
Answered by: jboon
Date published: 2017-02-22

Pumping lower than 40mm

You said in answer to my question about how low will it pump it will go below 40mm by manually operate the float switch, but can you explain how you do this? By holding the float lower for example? Or turning the automatic switch off? Thanks Russell
Asked by: Russell123
Hello Russell123, Please see below information from the instruction manual on how this can be done. If the water is not pumped after 20 seconds of starting, lower the float switch and lift the pump. Wait until the pump is emptied. Immerse the whole pump in water. If the product does not pump after several attempts, the water level is too low to seal the system. Thank you for using Q & A.
Answered by: Dcoz
Date published: 2017-01-13

How low will it drain?

I need this to drain as low as possible, re down to a few mm will this do the job?
Asked by: Russell123
Hello Russell123, The instruction manual states that the pump will automatically cut off when the water level drops below approximately 40mm. You can pump water levels below this however you would need to manually operate the float switch. Thank you for using Q&A.
Answered by: LMac
Date published: 2017-01-12

What angle does the switch have to reach before turning on ?Mine has to reach nearly vertical.

I dont know if my pump is in enough depth of water for the switch to operate.What is min. depth?
Asked by: theneck
The theneck. The dirty water pump needs about 50mm/2" of water or more to work. Thank you for using Q&A.
Answered by: yeldarb
Date published: 2017-01-27

Any parts that can rust? You've been asked twice if it can be submerged but you've got 2 contradictory answers. I want a pump that i can leave in purified water and i can't have a pump that will corrode over time and contaminate the water.

Can i leave this permanently in the 400l tank and use only when i transfer the water when required?
Asked by: Cinelliman123
Hello Cinelliman123, Eventually parts will degrade as with anything submerged in water, how long this takes really depends on the quality of the water etc. In the instruction manual it gives a general safety warning to "rest it for 10 min after each 1 hour running.", as it is not designed for continuous usage. Thank you for using Q and A.
Answered by: Chubbtonk
Date published: 2016-12-15
  • y_2017, m_2, d_24, h_17CST
  • bvseo_bulk, prod_bvqa, vn_bulk_0.0
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_25
  • loc_en_GB, sid_65041, prod, sort_[SortEntry(order=LOCALE, direction=DESCENDING), SortEntry(order=FEATURED, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_screwfix
Specification
Brand Titan
Cable Length 10 m
Hose Diameter (Imperial) 1" / 1¼ "
Manufacturer Guarantee 2 Year Manufacturer's Guarantee (T&Cs Apply)
Max. Pump Flow Rate 150 Ltr/min
Max Pump Head Size 6 m
Model No TTB582PMP
Pack Size 1
Pieces in Pack/Case 1
Power Output (Watts/Kw) 400 W
Power Voltage Supply 240 V
Product Type Automatic Dirty Water Pump
Total Product Weight 5.7 kg

Weight: 5.7kg. 240V. Pumps up to 150Ltr/min. Max. head 6m. Max. immersion depth 6m. Includes 1" and 1¼" adaptors and 10m cable.

Downloads

Instruction Manual