Browse store

Titan TCT Saw Blades 80T 250mm x 16 / 25 / 30mm (75549)

Long-life tungsten carbide-tipped circular saw blades that give performance and value. Very fine cut in plastic and non-ferrous metals. Perfectly suited to cutting parquet, laminate, epoxy, glass fibre and cement-bonded fibre boards.

  • Fine & Clean Cut
  • Cutting Width (Kerf): 2.6mm
  • Tungsten Carbide Teeth
  • Rake Angle: -5°
  • Model No:

More Info

Bulk saving available

Qty Price per item
1 £33.99
2 + £28.89
£33.99INC VAT

Add to basket for...

Rated 4.1 out of 5 by 11 reviewers.
  • 2016-08-28 T10:44:27.848-05:00
  • bvseo_lps, prod_bvrr, vn_prr_5.6
  • cp-1, bvpage1
  • co_hasreviews, tv_11, tr_11
  • loc_en_US, sid_75549, prod, sort_default

Add to saved list...

Rated 5 out of 5 by 80 T Blade Bought this to cut 3mm mdf. Used with Titan table saw and cut perfectly, giving an edge as good as the manufactures finish. Also cut some 9mm melamine faced mdf and achieved a clean finish. Seems like an ideal blade for fine work. 16 Jun 2016
Rated 5 out of 5 by Sawblade Does what it says on the box good value ! Will buy again 25 Apr 2016
Rated 5 out of 5 by 80T saw blade Needed to make sure I didn't chip the edges of some high quality MDF and chip board products for a new kitchen. This blade did the job (mounted in an Erbuaer table saw 13 Apr 2016
Rated 5 out of 5 by Good clean cut Used on a McKellar MCKM23 table saw: used a rubber grommet inside the arbor washer to press the 30/16 adapter bush onto arbor face as there was enough room inside cup of the washer for it to fall into. Tested by cutting lengths of 15mm MFC with blade height set to about 25mm above table. Very smooth finish to the chipboard, clean on top face and bottom faces. Just a microscopic amount of chipping on the bottom face - smaller than 0.2mm. Also tried some 22mm oak floor boards, clean upper face and very small amount of chipping on lower - with a cross cut - so to be expected. Almost planed like face on timber with no rotational saw markings. Tested cutting 10mm HDPE sheet, clean upper face and small amount of swarf on lower face but still very good. Overall, I am very pleased with the blade and its ability to produce a good clean finish on the materials I tried, the 2 types of cutting tip on the blade edge and thickness of the blade help this. Keeping the blade as shallow as possible helps to reduce the very tiny amounts of surface chipping on lower face as will taping or using scrap piece for backing - but for 15mm MFC just a shallow blade is fine. 2 Apr 2016
  • 2016-08-28 T10:44:27.848-05:00
  • bvseo_lps, prod_bvrr, vn_prr_5.6
  • cp-1, bvpage1
  • co_hasreviews, tv_11, tr_11
  • loc_en_US, sid_75549, prod, sort_default
Page : 2 next>
1 Question  1 Answer

Screwfix Q&A

Ask your questions. Share your answers.

« Back
Cannot remove w/top I have Makita circular saw and don`t want to chip the w/top edge and I know c/saw cuts upwards
28 Oct 2015
Customer avatar
Read all my Q&A
0out of 0found this question helpful.
Was this helpful?Yes0No0


Hi, If you clamp a sacrificial piece on the top of the work top this should help reduce any fragmenting.
5 Aug 2016
Customer avatar
Read all my Q&A
1of 1found this answer helpful.
Was this helpful?Yes1No0
1 of 1
  • 2016-08-28 T10:43:14.991-05:00
  • bvseo_lps, prod_bvqa, vn_prr_5.6
  • cp-1, bvpage1
  • co_hasquestionsanswers
  • loc_en_US, sid_75549, prod, sort_default
1 of 1
Brand Titan
Cutting Width 2.6 mm
Disc Bore Size 16/25/30 mm
Number of Teeth 80
Pack Size 1
Pieces in Pack/Case 1
Product Diameter 250 mm
Product Type Circular Saw Blade
Suitable Application For Cutting Aluminium or Plastic
Total Product Weight 944 kg
Type of Cut Fine & Clean Cut

Diameter 250mm. Number of teeth 80. Cutting bore 16 or 25 or 30mm. Fine cut and clean. For cutting aluminium / plastic.


Instruction Manual