Browse store

LAP 2-Gang 45A DP Cooker Switch Black Nickel (33300)

Clip-on front plate with cutting edge design for a 2-gang cooker switch. Includes black insert. BS EN 60669-1.

  • Screwless for a Flawless Finish
  • Flat Plate Profile

More Info

Bulk saving available

Qty Price per item
1 - 4 £10.31
5 + £9.23
£10.31INC VAT

Add to basket for...

Rated 4 out of 5 by 1 reviewer.
  • 2016-10-27 T08:47:16.902-05:00
  • bvseo_lps, prod_bvrr, vn_prr_5.6
  • cp-1, bvpage1
  • co_hasreviews, tv_1, tr_1
  • loc_en_US, sid_33300, prod, sort_default

Add to saved list...

Rated 4 out of 5 by Looks ok when mounted Purchased a set of switches and sockets to go in the kitchen. They all installed without issue. Medium quality but good looks. 23 Nov 2015
  • 2016-10-27 T08:47:16.902-05:00
  • bvseo_lps, prod_bvrr, vn_prr_5.6
  • cp-1, bvpage1
  • co_hasreviews, tv_1, tr_1
  • loc_en_US, sid_33300, prod, sort_default
1-1 of 1
1 Question  1 Answer

Screwfix Q&A

Ask your questions. Share your answers.

« Back
12 Jun 2016
Customer avatar
Read all my Q&A
0out of 0found this question helpful.
Was this helpful?Yes0No0


Hello Colmans.

Fitting and Wiring Instructions

1). Before commencing work, isolate the mains power supply and remove the fuse in the fuse box or switch off the circuit breaker in the consumer unit.
2). If unit is to be used as a replacement for an existing product, remove existing unit from its location and disconnect the wiring.
3). Connect the wires as shown in appropriate wiring diagrams overleaf. Use green/yellow sleeving on earth conductors not insulated. Ensure terminals are properly tightened and no bare wire is visible. Push back unit into mounting box making sure conductors are not trapped.
4). Screw the unit module to the mounting box, please ensure screws are sufficiently tight to support the product but please do not over tighten as this may cause some deformation.
5). Place the decorative front cover plate over the module and press firmly top and bottom until all retaining clips have fully clipped into position. To remove the decorative front cover plate, carefully insert a 3mm terminal screwdriver into the bottom slots and lift upward until the retaining clips disengage from the plastic grid moulding.
Please ensure the decorative plate is held as it is released to avoid it being dropped and damaged.
6). These products must be installed in accordance with the latest Building and IEE wiring regulations. If in any doubt, please contact a qualified electrician.

Thank you for using Q and A.
15 Jun 2016
Customer avatar
Read all my Q&A
, Maintenance
0of 0found this answer helpful.
Was this helpful?Yes0No0
1 of 1
  • 2016-10-27 T08:47:58.077-05:00
  • bvseo_lps, prod_bvqa, vn_prr_5.6
  • cp-1, bvpage1
  • co_hasquestionsanswers
  • loc_en_US, sid_33300, prod, sort_default
1 of 1
Brand LAP
Finish Black Nickel
Model No 8286MPI/NK
No. of Gangs 2
Pack Size 1
Parent Colour Black
Pieces in Pack/Case 1
Product Height 44.98 mm
Product Length 148.8 mm
Product Type Cooker Switch
Product Width 88.8 mm
Profile Type Flat Screwless
Switches & Sockets Finish Polished
Switches & Sockets Product Type Cooker Switch
Switches & Sockets Profile Type Flat Screwless
Total Product Weight 0.31 kg