0500 41 41 41
Cookie Reports - Screwfix Cookie Policy

Wera

Impaktor TriTorsion Ringmagnet Bit Holder

Product Code: 46593

Rated 3.5 out of 5 by 4 reviewers.

TriTorsion bit holder, designed for use with cordless impact drivers. Holds screws up to 254mm.

View more information

Product contents:
1 x 75mm bit holder.

£15.49 (inc. 20% VAT)

£15.49
3.5 5 4

Add to saved list


Available for deliveryNext Day Delivery
Available for collection from store Store Collection Check stock in your store
Page 1 of 4
Rated 5 out of 5 by 6000 10x4's can't be bad!! This bit holder is expensive but massively outlasted all others i have used.used with 18v makita impact driver besides the 6000 10x4's into 9x2 timber and the 6in screws the magnet comfortably holds solid it's also done around 400 joist hangers with 20 1-3/4 screws in each finally wearing out. HIGHLY RECOMMENDED AND AM ON MY 3RD. I HONESTLY DON'T BUY ANYTHING ELSE. Might be pricey for the DIYer but if you're a heavy user you can't go wrong with this 17 Mar 2013
Rated 4 out of 5 by Good Mainly 4 Impact Drivers? This is one of the most expensive bit holders available, so is it worth paying the premium? I've found quite a few pros & cons which may not be entirely obvious, particularly if you haven't had a chance yet to handle this product.... Firstly, the holder is very solidly engineered. So much so, though, that it is quite heavy compared to most other holders of a similar length. Not an issue when used on big power tools, but might become a factor on compact units & hand tools/ drivers. The bit can be a little tricky to grip & remove from the holder because 25mm bits only stick out of the holder by about 11mm, & the magnet which holds it is quite strong. But if you use a longer, 50mm bit, the 2nd magnet, a ring magnet which is intended to hold the fastener/ screw in place, can't be used because it only extends 10mm & wouldn't reach the screw head. Also, it is quite hard to see where the bit is when, say, trying to manoeuvre it into position onto a screw already in a wall, because the holder is quite wide & it obscures the view of the (only) 11mm of bit which sticks out. The advantage of this holder using a ring magnet system are that it can hold larger screw heads than holders which use a system with a sleeve that slides, because it only hangs on to the outer head of the screw, & doesn't have to slide over it. It also means the screw sits nice & squarely on the holder. The downside of the ring magnet system are that you usually either need to use your 2nd hand to steady the screw when first driving it in, or need a pilot hole, because it often doesn't hold the screw strongly enough to prevent it from falling off. Thus overall, I'd probably say not to get this holder if you only do lighter-duty jobs, & go for something cheaper, thinner & lighter etc, & possibly with a sliding sleeve. But for the jobs for which this has mainly been designed, heavy duty fastening using an impact driver, it is probably money well spent. I still have 2 questions regarding this tool, though... Will repeated concussion from the impact driver eventually weaken the magnetism? Only time will tell. Also, this TriTorsion holder, in combination with using TriTorsion bits (which aren't strictly necessary) are designed to gives maximum absorption of the stress-inducing blows from an impact driver. Though I do wonder, then, what was the point of using an impact driver in the first place?! 14 Jun 2012
Rated 4 out of 5 by Does the job well Just decided to write this as I read a review above that said that the magnet would not hold the screws in place. The sleeve needs to be slid forward for the magent to work, when it is slid forward it holds the screws very well. Bit expensive but hopefully it will last well with my Makita impact driver, only put in a couple of hundred screws so far. 9 May 2012
Rated 1 out of 5 by Wera impactor tritortion drive Sory Wera i like your bits but this driver would not hold 6guage screws!! i returned it for a no quibble refund 19 Jul 2011
1-4 of 4

Specification

Brand Wera
Model No 897/4 IMP R SB
Pack Size 1
Product Length 150 mm
Product Thickness 15 mm
Product Width 60 mm
Total Product Weight 0.09 kg